Rockwell Automation 1771-QDC, D17716.5.93(Passport) PLASTIC MOLDING MODULE - Manual (Page 150)

Enter Your Values Here
Load Initial Profile Setpoints
Chapter 8
8-33
Worksheet 8-E
(continued)
Clamp Open Profile Block (OPC)
Control Word ProĆSet 600 Addr. Value Description Units
OPC09 N43:545 * FOC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC10 N43:546 * FOC Segment 1 Pressure Setpoint Pressure 3
OPC11 N43:547 * FOC EndĆof Segment 1 Position Setpoint Incremental Distance 4
OPC12 N43:548 * FOC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC13 N43:549 * FOC Segment 2 Pressure Setpoint Pressure 3
OPC14 N43:550 * FOC EndĆof Segment 2 Position Setpoint Incremental Distance 4
OPC15 N43:551 * FOC Segment 3 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC16 N43:552 * FOC Segment 3 Pressure Setpoint Pressure 3
OPC17 N43:553 * FOC EndĆof Segment 3 Position Setpoint Incremental Distance 4
OPC18 N43:554 0 SOC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC19 N43:555 0 SOC Segment 1 Pressure Setpoint Pressure 3
OPC20 N43:556 0 SOC EndĆof Segment 1 Position Setpoint Incremental Distance 4
OPC21 N43:557 0 SOC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC22 N43:558 0 SOC Segment 2 Pressure Setpoint Pressure 3
OPC23 N43:559 0 SOC EndĆof Segment 2 Position Setpoint Incremental Distance 4
OPC24 N43:560 0 SOC Segment 3 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC25 N43:561 0 SOC Segment 3 Pressure Setpoint Pressure 3
OPC26 N43:562 0 SOC EndĆof Segment 3 Position Setpoint Incremental Distance 4
OPC27 N43:563 0 TOC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC28 N43:564 0 TOC Segment 1 Pressure Setpoint Pressure 3
OPC29 N43:565 0 TOC EndĆof Segment 1 Position Setpoint Incremental Distance 4
OPC30 N43:566 0 TOC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC31 N43:567 0 TOC Segment 2 Pressure Setpoint Pressure 3
OPC32 N43:568 0 TOC EndĆof Segment 2 Position Setpoint Incremental Distance 4
OPC33 N43:569 0 TOC Segment 3 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC34 N43:570 0 TOC Segment 3 Pressure Setpoint Pressure 3
OPC35 N43:571 0 TOC EndĆof Segment 3 Position Setpoint Incremental Distance 4
OPC36 N43:572 * OSC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC37 N43:573 * OSC Segment 1 Pressure Setpoint Pressure 3
OPC38 N43:574 0 OSC EndĆof Segment 1 Position Setpoint Incremental Distance 4
OPC39 N43:575 0 OSC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
OPC40 N43:576 0 OSC Segment 2 Pressure Setpoint Pressure 3
OPC61 N43:597 * Start OSC Position Setpoint Incremental Distance 4
OPC62 N43:598 * Mold Open Position Setpoint Incremental Distance 4
OPC63 N43:599 0 Mold Open Dwell Timer Preset Time 5
1 Percent of Maximum Velocity 2 Velocity along Axis 3 Pressure
00.00 to 99.99 00.00 to 99.99 inches per second 0000 to 9999 PSI
000.0 to 999.9 millimeters per second 000.0 to 999.9 Bar
4 Axis Measured from MCC27 (if nonĆzero) or MCC23 5 Time
00.00 to 99.99 inches 00.00 to 99.99 seconds
00.00 to 999.9 millimeters
* Refer to the appropriate section later in this chapter for information on this parameter