Rockwell Automation 1771-QDC, D17716.5.93(Passport) PLASTIC MOLDING MODULE Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for 1771-QDC, D17716.5.93(Passport) PLASTIC MOLDING MODULE Rockwell Automation
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 306 |
| Size: | 1.99 MB |
Show table of contents
Document Outline
- 1771-6.5.93, Plastic Molding Module, Inject, Clamp, and Eject Mode
- Inside Cover
- Table of Contents
- Preface
- Chapter 1 - Overview of Inject, Clamp, and Eject Mode
- Chapter 2 - Install the QDC Module
- Chapter 3 - Configure the QDC Module's I/O
- Chapter 4 - Overview of Remaining Configuration Procedures
- Chapter 5 - Jog Your Machine
- Chapter 6 - Select Command and Status Bits to Sequence Machine Operation
- Chapter 7 - Load Initial Configuration Values
- Chapter Objectives
- Use These Worksheets
- Procedure to Determine and Record Initial Values
- Determine Bit Selections: Assign Module Outputs for Your Control Valves
- Select the Type of PID Algorithm
- Determine Word Values: Select Values for Expert Response Compensation (ERC)
- Determine Unselected Valve Set-output Values
- Set Your Acceleration/Deceleration Ramp Rates
- Determine Set output Values for End of Profiles
- Set Pressure Control Limits
- Set Velocity Control Limits
- Enter and Download your Worksheet Values
- Chapter 8 - Load Initial Profile Values
- Chapter Objectives
- Use These Worksheets
- Determine and Record Setpoints for the Clamp Close Profile (CPC)
- Determine Bit Selections for Worksheet 8-A
- Determine Word Values for Worksheet 8-A
- Enter and Download Your Worksheet Values
- Determine and Record Setpoints for the Injection Profile (IPC)
- Determine Bit Selections for Worksheet 8-B
- Determine Word Values for Worksheet 8B
- Enter and Download your Worksheet Values
- Determine and Record Setpoints for the Pack/Hold Profile (HPC)
- Determine Bit Selections for Worksheet 8-C
- Determine Word Values for Worksheet 8-C
- Enter and Download your Worksheet Values
- Determine and Record Setpoints for the Plastication Profile (PPC)
- Determine Bit Selections for Worksheet 8-D
- Determine Word Values for Worksheet 8-D
- Enter and Download your Worksheet Values
- Determine and Record Setpoints for the Clamp Open Profile (OPC)
- Determine Bit Selections for Worksheet 8-E
- Determine Word Values for Worksheet 8-E
- Enter and Download Your Worksheet Values
- Determine and Record Setpoints for the Ejector Profile (EPC)
- Determine Bit Selections for Worksheet 8-F
- Determine Word Values for Worksheet 8-F
- Enter and Download Your Worksheet Values
- Chapter 9 - Span Your Valves
- Chapter Objectives
- Referenced Worksheets
- LPC Profile - Low Pressure Valve
- FCC, SCC, TCC Profiles
- FCC, SCC, TCC Profiles - Velocity (Flow) Valve (s)
- INC Profile Pressure Valve
- INC Profile - Velocity Valve
- PKC and HDC Profiles - Pressure Valves
- PLC Profile - Pressure Valve
- FOC, SOC, TOC, OSC Profiles- Velocity (Flow) Valve(s)
- EAC, ERC Profiles - Pressure Valve(s)
- EAC, ERC Profiles - Velocity (FLOW) Valve(s)
- Chapter 10 - Tune Your Machine
- Chapter 11 - Troubleshoot with LEDs
- Appendix A - Blank Worksheets
- Index
- Inside Back Cover
- Back Cover