Rockwell Automation 1771-QDC, D17716.5.93(Passport) PLASTIC MOLDING MODULE - Manual (Page 121)

Enter Your Values Here
Load Initial Profile Setpoints
Chapter 8
8-4
Worksheet 8-A
(continued)
Clamp Close Profile Block (CPC)
Control Word ProĆSet 600 Addr. Value Description Units
CPC09 N43:245 * FCC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC10 N43:246 * FCC Segment 1 Pressure Setpoint Pressure 3
CPC11 N43:247 * FCC EndĆof Segment 1 Position Setpoint Incremental Distance 4
CPC12 N43:248 * FCC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC13 N43:249 * FCC Segment 2 Pressure Setpoint Pressure 3
CPC14 N43:250 * FCC EndĆof Segment 2 Position Setpoint Incremental Distance 4
CPC15 N43:251 * FCC Segment 3 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC16 N43:252 * FCC Segment 3 Pressure Setpoint Pressure 3
CPC17 N43:253 * FCC EndĆof Segment 3 Position Setpoint Incremental Distance 4
CPC18 N43:254 0 SCC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC19 N43:255 0 SCC Segment 1 Pressure Setpoint Pressure 3
CPC20 N43:256 0 SCC EndĆof Segment 1 Position Setpoint Incremental Distance 4
CPC21 N43:257 0 SCC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC22 N43:258 0 SCC Segment 2 Pressure Setpoint Pressure 3
CPC23 N43:259 0 SCC EndĆof Segment 2 Position Setpoint Incremental Distance 4
CPC24 N43:260 0 SCC Segment 3 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC25 N43:261 0 SCC Segment 3 Pressure Setpoint Pressure 3
CPC26 N43:262 0 SCC EndĆof Segment 3 Position Setpoint Incremental Distance 4
CPC27 N43:263 0 TCC Segment 1 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC28 N43:264 0 TCC Segment 1 Pressure Setpoint Pressure 3
CPC29 N43:265 0 TCC EndĆof Segment 1 Position Setpoint Incremental Distance 4
CPC30 N43:266 0 TCC Segment 2 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC31 N43:267 0 TCC Segment 2 Pressure Setpoint Pressure 3
CPC32 N43:268 0 TCC EndĆof Segment 2 Position Setpoint Incremental Distance 4
CPC33 N43:269 0 TCC Segment 3 Velocity Setpoint Percent of Maximum Velocity 1 or Velocity along Axis 2
CPC34 N43:270 0 TCC Segment 3 Pressure Setpoint Pressure 3
CPC35 N43:271 0 TCC EndĆof Segment 3 Position Setpoint Incremental Distance 4
CPC37 N43:273 * LPC Segment 1 Pressure Setpoint Pressure 3
CPC38 N43:274 0 LPC EndĆofĆSegment 1 Position Setpoint Incremental Distance 4
CPC40 N43:276 0 LPC Segment 2 Pressure Setpoint Pressure 3
CPC61 N43:297 * Start LPC Position Setpoint Incremental Distance 4
CPC62 N43:298 * Mold Safe Position Setpoint Incremental Distance 4
CPC63 N43:299 0 Tonnage Complete Pressure Setpoint Pressure 3
1 Percent of Maximum Velocity 2 Velocity along Axis 3 Pressure 4 Axis Measured from MCC27
00.00 to 99.99 00.00 to 99.99 Inches per Second 0000 to 9999 PSI (if nonĆzero) or MCC23
000.0 to 999.9 Millimeters per Second 000.0 to 999.9 Bar 00.00 to 99.99 Inches
00.00 to 999.9 Millimeters
* Refer to the appropriate section later in this chapter for information on this parameter