HP MPX200 Multifunction Router User Manual

Page 96

0 50:06:01:62:41:e0:49:2e, 61-00-00 DGC RAID-0 Src+Dest
1 50:00:1f:e1:50:0a:37:19, 82-0c-00 HP HSV210-1 Src+Dest

Please select a Destination Target from the list above ('q' to quit): 1

Index (VpGroup Name)
----- --------------
1 VPGROUP_1

Please select a VPGroup for Destination LUN ('q' to quit): 1

LUN Vendor LUN Size( GB) Attributes Serial Number/WWULN
--- ------ -------------- ---------- -------------------
1 HP 10.000 PA299B1AASZ024
60:05:08:b4:00:05:4d:94:00:01:30:0b:fe:5a:00:00
2 HP 10.000 PA299B1AASZ024
60:05:08:b4:00:05:4d:94:00:01:30:0b:fe:5d:00:00
3 HP 10.000 PA299B1AASZ024
60:05:08:b4:00:05:4d:94:00:01:30:0b:fe:60:00:00
4 HP 10.000 PA299B1AASZ024
60:05:08:b4:00:05:4d:94:00:01:30:0b:fe:63:00:00
5 HP 100.000 DATA MGMT PA299B1AASZ024
60:05:08:b4:00:05:4d:b0:00:01:50:1a:94:ad:00:00

Please select a LUN as a Destination Lun('q' to quit): 1
Destination LUN appears to contain some valid data.
Are you sure you want to continue? (y/n) : y
Is destination LUN a thin provisioned LUN [y/n]: n
I/O Size (0=32KB, 1=64KB, 2=128KB, 3=512KB, 4=1MB) [64KB ]
Please Enter a Job Description (Max = 127 characters)
default name [ DGC RAID-0:VPG1:004 to HP HSV210-1:VPG1:001 ]
Index Group Owner Group Name
----- ----------- ----------
0 1 Group 0

Please select a Group that this Job should belong to [0]
Start Time (1=Now, 2=Delayed, 3=JobSerialScheduling, 4=ConfigureOnly) [Now ]
Successfully created Job
All attribute values for that have been changed will now be saved.

To schedule an individual data migration job in the CLI:
1.

Log into the MPX200 as guest and enter the password.

Open a miguser session using the following command:

miguser start -p migration

(The default password for miguser is migration.)

To create a migration job, enter the following command:

migration add

When the CLI prompts you to select a migration type, enter either 1 to select Offline (Local or
Remote), 2 to select Online (Local), or 3 to select Online (Remote).

The CLI lists the source arrays that you have previously defined and prompts you to select one.

Select a source array.

From the selected source array, the CLI lists the VP Groups.

Select a VP Group for the Source LUN.

The CLI lists the LUNs that have been exposed to the selected VP Group on the MPX200 for
migration and prompts you to select one LUN.

Select a LUN for data migration.

The CLI lists the destination arrays that you have previously defined.

Select a VP Group for the destination LUN.

From the selected destination array, the CLI lists the LUNs that have been exposed to the
MPX200 for migration.

Select one LUN. The destination LUN you select should not be a part of any other job, and
its size should be equal to or greater than the source LUN.

Command line interface