Extron Electronics DMS 1600_2000_3200_3600 User Guide User Manual
Page 65
DMS 1600, DMS 2000, DMS 3200, and DMS 3600 • Programming Guide
59
Command and Response Table for IP-specific SIS Commands
Command
ASCII Command
(host to unit)
Response
(unit to host)
Additional description
IP setup commands
Set matrix name
EX3)
CN
}
Ipn•
X3)]
Up to 240 alphanumeric characters.
Set matrix name to factory
default
E
•CN
}
Ipn•
X3!]
“DMS-nn00” plus the last 3 pairs of the MAC
address. nn is either “16,” “20,“ “32,”or “36.”
Read matrix name
E
CN
}
X3)]
Set time and date
EX3@
CT
}
Ipt
X3@]
Read time and date
E
CT
}
X3#]
Set GMT offset
EX3$
CZ
}
Ipz
X3$]
In the command, the divider between hours and
minutes can be either a colon or a period. In the
response divider is a colon.
Example:
E
8.0CZ
}
Ipz08:00
]
GMT +8:0 hours.
Set Daylight Saving Time
EX3%
CX
}
Ipx
X3%]
Read Daylight Saving Time
E
CX
}
X3%]
Set IP address
EX3^
CI
}
Ipi
X3^]
Read IP address
E
CI
}
X3^]
Read hardware (MAC) address
E
CH
}
X3&]
Read # of open connections
E
CC
}
X3*]
Set subnet mask
EX3^
CS
}
Ips
X3^]
Read subnet mask
E
CS
}
X3^]
Set gateway address
EX3^
CG
}
Ipg
X3^]
Read gateway address
E
CG
}
X3^]
Set administrator password
EX3(
CA
}
Ipa•
X3(]
Read administrator password
E
CA
}
X3(]
Reset (clear) administrator
password
E
•CA
}
Ipa•
]
Set user password
EX3(
CU
}
Ipu•
X3(]
Read user password
E
CU
}
X3(]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set mail server IP address,
domain name, password
EX3^
,
X4)
,
X3(
CM
}
Ipm
X3^
,
X4)
,
X3(]
Read mail server IP address,
domain name, password
E
CM
}
X3^
,
X4)
,
X3(]
Set e-mail recipient
EX4!
,
X4@
CR
}
Ipr
X4!
,
X4@
,
]
This command sets the recipient. To receive e-mail
notifications, you must then set the events that
the switcher reports, using one or more separate
Set e-mail events (EM) commands (see below).
Example:
E
}
Ipr72,[email protected],
]
Read e-mail recipient
EX4!
CR
}
X4@
,
]
Set e-mail events for
recipient
E
I
X4#X4!
,
X4$
,
X4%
EM
}
Ipe
X4#
,
X4!
,
X4$
,
X4%]
You must first have set an e-mail recipient for the
e-mail account number (
X4!
), using the separate
Set e-mail (CR) command (see above).
Example:
E
I72,0,3EM
}
Ipe*72*0*3
]
E-mail account #72 (recipient #8) (Jsmith, as set by
the preceding Set e-mail recipient command), will
receive fail/missing and fixed/restore messages for
all inputs.
Read e-mail events for
recipients
EX4#X4!
,
X4$
EM
}
X4%
,
X4%
,
X4%
,...,
X4%]