Yaskawa VS-626 MC5 - Manual (Page 286)

12.5 User Constants
- 17
Table 12.1 User Constants (Continued)
No.
Name
(Display)
Factory
Setting
Setting No.
Name
(Display)
Factory
Setting
Setting
E4-05 Motor 2 mid. output frequency voltage 1 1
(V/F2 Mid Voltage)
11.0
2
F5-02 Channel 2 output selection
(DO-02 Ch2 Select) 1
E4-06 Motor 2 min. output frequency
(V/F2 Min Freq) 0.5 F6-01 Output mode selection
(DO-08 Selection) 0
E4-07 Motor 2 min. output frequency voltage 1
(V/F2 Min Voltage)
2.0
2
F7-01 Frequency multiple selection
(PO-36F Selection)
1
E5-01 Motor 2 rated current 1
(Motor 2 rated FLA)
1.9
3
F8-01 Transmission option (SI-F/G) 1
(E-15 Det Sel)
1
E5-02 Motor 2 rated slip 1
(Motor 2 Slip Freq)
2.90
3
F9-01 External fault input level from transmissin op-
tion (FF0 Selection)
1 0
E5-03 Motor 2 no-load current 1
(Motor 2 No-load I)
1.20
3
F9-02 External fault detection from transmission op-
tion (EF0 Detection)
1 0
E5-04 Motor 2 number of poles 1
(Motor 2 # Poles)
4 poles F9-03 Action for external fault from transmission op-
tion (EF0 Fault Act)
1 1
E5-05 Motor 2 line-to-line resistance 1
(Motor 2 term Ohms)
9.842
3 F9-04 Transmission option trace sampling time
(Trace Sample Time)
1 0
E5-06 Motor 2 leak inductance 1
(Motor 2 Leak)
18.2
3
H1-01 Multi-function input (terminal 3)
(Terminal 3 Sel)
24
F1-01 PG constant
(PG Pulse/Rev)
600 H1-02 Multi-function input (terminal 4)
(Terminal 4 Sel)
14
F1-02 Operation selection at PG open circuit
(PG Fdbk Loss Sel) 1 H1-03 Multi-function input (terminal 5)
(Terminal 5 Sel) 3 (0)
5
F1-03 Operation selection at overspeed
(PG Overspeed Sel) 1 H1-04 Multi-function input (terminal 6)
(Terminal 6 Sel) 4 (3)
5
F1-04 Operation selection at deviation
(PG Deviation Sel) 3 H1-05 Multi-function input (terminal 7)
(Terminal 7 Sel) 6 (4)
5
F1-05 PG rotation
(PG Rotation Sel) 0 H1-06 Multi-function input (terminal 8)
(Terminal 8 Sel) 8 (6)
5
F1-06 PG division rate (PG pulse monitor)
(PG output Ratio)
1 H2-01 Multi-function input (terminal 9-10)
(Terminal 9 Sel)
0
F1-07
Integral value during accel/decel enable/dis-
able
(PG Ramp PI/I Sel)
0 H2-02 Multi-function input (terminal 25-27)
(Terminal 25 Sel) 1
F1-08 Overspeed detection level
(PG Overspd Level) 115 H2-03 Multi-function input (terminal 26-27)
(Terminal 26 Sel) 2
F1-09 Overspeed detection delay time
(PG Overspd Time) 0.0
4
H3-01 Signal level selection (terminal 13)
(Term 13 Signal) 0
F1-10 Excessive speed deviation detection level
(PG Deviate level)
10 H3-02 Gain (terminal 13)
(Terminal 13 Gain)
100.0
F1-11 Excessive speed deviation detection delay time
(PG Deviate Time) 0.5 H3-03 Bias (terminal 13)
(Terminal 13 Bias) 0.0
F1-12 Number of PG gear teeth 1
(PG# Gear Teeth 1) 0 H3-04 Signal level selection (terminal 16)
(Term 16 Signal) 0
F1-13 Number of PG gear teeth 2
(PG# Gear Teeth 2)
0 H3-05 Multi-function analog input (terminal 16)
(Terminal 16 Sel)
0
F1-14 PG open-circuit detection time 1
(PGO Time) 2.0 H3-06 Gain (terminal 16)
(Terminal 16 Gain)
100.0
F2-01 Bi-polar or uni-polar input selection
(AI-14 Input Sel) 0 H3-07 Bias (terminal 16)
(Terminal 16 Bias) 0.0
F3-01 Digital input option
(DI Input) 0 H3-08 Signal level selection (terminal 14)
(Term 14 Signal) 2
F4-01 Channel 1 monitor selection
(AO Ch1 Select)
2 H3-09 Multi-function analog input (terminal 14)
(Terminal 14 Sel)
1F
F4-02 Channel I gain
(AO Ch1 Gain) 1.00 H3-10 Gain (terminal 14)
(Terminal 14 Gain) 100.0
F4--03 Channel 2 monitor selection
(AO Ch2 Select) 3 H3-11 Bias (terminal 14)
(Terminal 14 Bias) 0.0
F4-04 Channel 2 gain
(AO Ch2 Gain)
0.50 H3-12 Analog input filter time constant
(Filter Avg Time)
0.00
F4--05 Channel 1 output monitor bias
(AO Ch1 Bias) 0.0 H4-01 Monitor selection (terminal 21)
(Terminal 21 Sel) 5
F4--06 Channel 2 output monitor bias
(AO Ch2 Bias) 0.0 H4-02 Gain (terminal 21)
(Terminal 21 Gain) 1.00
F5-01 Channel 1 output selection
(DO-02 Ch1 Select)
0 H4-03 Bias (terminal 21)
(Terminal 21 Bias)
0.0
* 1. Not displayed for some models depending on software version No.
* 2. Setting for 200 V class Inverters. For 400 V class Inverters, double the value.
* 3. Setting unit and initial setting depend on Inverter capacity.
* 4. Depends on the control method (A1-02).
* 5. Factory setting in the parentheses is for 3-wire sequence.
12