Comtech EF Data HPCST-5000 - Manual (Page 171)

Rev. 1 i–1
I
Index
Address Byte, 2–25, 3–28
Analog, A–2, A–4, A–6
Analog Status Circuits, 2–18, 2–19, 2–23, 2–24, 2–32, 2–
35, 2–36, 3–33, 4–7
ASCII Reference Information, 2–19, 2–23, 2–32, 2–35
Auxiliary Interface, A–8
Basic Controls and Indicators, 3–32, 3–33
Cabinet Slide Assembly, 6–4
Check Byte, 3–25
Clearing a Fault, A–5, A–6
Clearing a Fault-LOCAL Control Configuration, 5–10
Command Message Format, A–4
Command Reject Argument, A–3
Communication Protocols, A–7
Component Descriptions, A–2, A–3
Control and Status Interface, 1–7, 1–10, 1–11, 2–18, 2–20,
2–21, 2–22, 2–24, 2–31, 2–32, 2–33, 2–36, 3–27, 3–30,
3–33, 4–2, 4–5, 5–3, 5–7, 5–10, 6–4, A–10, A–13, A–
17
Control and Status Signals, 4–2
Control Interfaces, 4–5
Control/Status Ground Isolation, 2–20, 2–32, 2–33
Controller Control Commands, 2–24
Controller Query Commands, A–13
Controls and Indicators, A–11
Digital Status, 5–3, 6–4
Digital Status Circuits, 2–19, 2–21, 2–32, 2–33, 4–6
Environment, 2–19, 2–21, 2–32, 2–33
External Interlock/Remote Functions, 2–31
Fault Reset Push Button Switch, 2–18, 2–20, 2–21, 2–22,
2–32, 2–33, 2–34, 2–36, 3–33, 4–2, 4–4, 4–5, 4–6, 4–7,
5–5, 5–10, 6–8, A–13, A–15, A–16, A–17, A–18
Heater Delay, A–3, A–6
High Voltage ON, 2–18, 2–20, 2–36, 3–33, 4–2, 4–3, 4–5
Included Parts, 2–3
Initial Power-On, 2–3
Introduction, 2–3
Lamp Test Push Button Switch, 2–3
LOCAL Control Configuration, 6–8
Local Controller Mode, 5–3, 5–10
Local Controls and Indicators, 6–9
Local/Remote Push Button Switch, 6–4
Low-Noise Amplifier (LNA) Assembly, 6–5
Manual or Automatic Switching, 4–10, 5–9
Manual/Automatic Push Button Switch, 6–4
Mechanical, 6–6
Normal Operation, 2–30, 2–36, 3–23
Operating Modes, 2–36
Operation and Control, 1–6, 1–7, 1–12, 2–1, 2–3, 2–25, 2–
26, 3–1, 3–3, 4–2, 6–3, 6–4, 6–9, 6–10
Operator Troubleshooting, 4–2
Output Voltage Circuits, 5–9
Overview, 2–19, 2–24, 2–32, 2–35
Parameters, 6–2, A–1
Parity, A–4, A–6, A–17
Performance, A–5, A–7, A–11, A–15, A–16
Power-On Sequence, 6–4, 6–5
Preventive Maintenance, 5–9
Prime Power, A–2, A–4
Receive, 1–6
Redundant System Command Set, 1–12
Remote Control Serial Interface, 5–3, 5–10
Response Byte, 6–9
RF Output (J5), A–6
RF TX Sample (J4), 2–26
Secondary Address Byte, 2–9, 3–11
Spar Installation, 4–9
Specifications, 3–14
Square Pole, 3–14
Standard Connections, 2–13, 3–14
System Interface, 2–18, 2–20, 2–32, 2–34, 2–36, 3–33, 4–
2, 4–3, 4–5, 6–3, 6–4, 6–7, A–11, A–13, A–15