Comtech EF Data HPCST-5000 - Manual (Page 14)

Table of Contents High-Power TWTA Satellite Terminals
x Rev. 1
Figures
Figure 1-1. HPCST-5000/-7000 and HPKST-12000 ............................................................................................... 1–1
Figure 1-2. TWTA Redundant Assembly (Typical)................................................................................................. 1–3
Figure 1-3. HPCST-5000/-7000 Redundant Terminal Systems Block Diagram (Typical) ...................................... 1–5
Figure 1-4. HPKST-12000 Redundant Terminal System Block Diagram (Typical)................................................ 1–6
Figure 1-5. 100W and 140W Unit Block Diagram .................................................................................................. 1–9
Figure 1-6. 300W and 350W Unit Block Diagram .................................................................................................. 1–9
Figure 1-7. HPC-1200 Single Thread Controller ................................................................................................... 1–10
Figure 1-8. HPC-1110 1:1 Redundant Controller .................................................................................................. 1–11
Figure 1-9. RSU-503L ........................................................................................................................................... 1–12
Figure 1-10. TWTA Outline Drawing (Typical) .................................................................................................... 1–28
Figure 1-11. HPC-1200 Outline Drawing .............................................................................................................. 1–29
Figure 1-12. HPC-1110 Outline Drawing .............................................................................................................. 1–30
Figure 2-1. Typical TWTA Spar Installation ......................................................................................................... 2–14
Figure 2-2. 100W and 140W TWTA External Connections .................................................................................. 2–16
Figure 2-3. 300W and 350W TWTA External Connections .................................................................................. 2–17
Figure 2-4. Interface Connector Pinouts ................................................................................................................ 2–19
Figure 2-5. TWT Temperature: Temperature vs. Voltage ..................................................................................... 2–23
Figure 2-6. Single Phase AC Power Connections ................................................................................................. 2–26
Figure 2-7. Single Thread System M&C Cable Harness (CA/5124)...................................................................... 2–29
Figure 2-8. HPC-1200 Outline Drawing ................................................................................................................ 2–30
Figure 2-9. HPC-1200 Rear Panel Connector Locations ....................................................................................... 2–31
Figure 2-10. Interface Connector Pinouts .............................................................................................................. 2–32
Figure 2-11. Digital Status Circuit Isolation .......................................................................................................... 2–33
Figure 3-1. HPCST/HPKST 1:1 Redundant System Cable Harness (CA/5122).................................................... 3–16
Figure 3-2. HPCST/KST 1:1 Redundant M&C System Interface Cable (Optional) (CA/5279) ............................ 3–18
Figure 3-3. HPCST/HPKST 1:1 Uplink-Only Redundant System Cable Harness (CA/5248)............................... 3–20
Figure 3-4. HPCST/HPKST HPCST/HPKST Single TWTA System Cable Harness (CA/5124) ......................... 3–22
Figure 3-5. HPC-1110 Outline Drawing ................................................................................................................ 3–24
Figure 3-6. Cabinet Slide Assemblies .................................................................................................................... 3–26
Figure 3-7. HPC-1110 rear Panel........................................................................................................................... 3–27
Figure 3-8. Prime Power Connector....................................................................................................................... 3–28
Figure 3-9. Waveguide Switch Connector Pinouts................................................................................................. 3–29
Figure 3-10. EIA-422, -485 Pinouts, COM2 Only ................................................................................................. 3–31
Figure 3-11. EIA-232-C Pinouts ............................................................................................................................ 3–32
Figure 3-12. Auxiliary interface Connector Pinouts............................................................................................... 3–33
Figure 3-13. “X” Insert Configuration ................................................................................................................... 3–34
Figure 3-14. Configuration 1, “X” Insert Panel...................................................................................................... 3–34
Figure 5-1. HPC-1200.............................................................................................................................................. 5–1
Figure 5-2. Typical Configuration............................................................................................................................ 5–2
Figure 5-3. Monitor Points and Lamp Test .............................................................................................................. 5–4
Figure 5-4. Fault Indicators...................................................................................................................................... 5–5
Figure 5-5. Status Indicators .................................................................................................................................... 5–6
Figure 5-6. HPC-1200 Local Controls ..................................................................................................................... 5–7
Figure 5-7. TEMP ANALOG Output Calibration.................................................................................................... 5–8
Figure 6-1. HPC-1110.............................................................................................................................................. 6–1
Figure 6-2. Basic HPC-1110 Rear Panel.................................................................................................................. 6–2