Brocade Virtual ADX Switch and Router Guide (Supporting ADX v03.1.00) User Manual
Brocade virtual adx, Switch and router guide
Table of contents
Document Outline
- Contents
- Preface
- Configuring Basic Features
- Configuring basic system parameters
- Entering system administration information
- Configuring Simple Network Management (SNMP) parameters
- Configuring SNMP version 3 traps
- Configuring an interface as the source for all Telnet packets
- Cancelling an outbound Telnet session
- Configuring an interface as the source for all TFTP packets
- Configuring CLI banners
- Configuring terminal display
- Checking the length of terminal displays
- Configuring basic port parameters
- Configuring basic Layer 2 parameters
- Configuring static MAC addresses
- Configuring system parameter settings
- Configuring basic system parameters
- Configuring Basic Layer 3
- Configuring Virtual LANs (VLANs)
- Configuring IP
- Basic configuration
- Overview
- Basic IP parameters and defaults
- Configuring IP parameters
- Configuring IP addresses
- Configuring Domain Name Server (DNS) resolver
- Changing the router ID
- Specifying a single source interface for Telnet, TACACS/TACACS+, or RADIUS packets
- Configuring ARP parameters
- Configuring forwarding parameters
- Disabling ICMP messages
- Disabling ICMP redirect messages
- Configuring static routes
- Configuring a default network route
- Configuring IP load sharing
- Configuring UDP broadcast and IP helper parameters
- Configuring BootP/DHCP forwarding parameters
- Displaying IP configuration information and statistics
- Rate Limiting
- Configuring OSPF
- Overview of OSPF
- Configuring OSPF
- Configuration rules
- OSPF parameters
- Enable OSPF on the router
- Assign OSPF areas
- Assigning an area range (optional)
- Assigning interfaces to an area
- Modify interface defaults
- Change the timer for OSPF authentication changes
- Block flooding of outbound LSAs on specific OSPF interfaces
- Assign virtual links
- Modify virtual link parameters
- Changing the reference bandwidth for the cost on OSPF interfaces
- Define redistribution filters
- Prevent specific OSPF routes from being installed in the IP route table
- Modify default metric for redistribution
- Enable route redistribution
- Disable or re-enable load sharing
- Configure external route summarization
- Configure default route origination
- Modify SPF Timers
- Modify redistribution metric type
- Modify administrative distance
- Configure OSPF group Link State Advertisement (LSA) pacing
- Modify OSPF traps generated
- Modify OSPF standard compliance setting
- Modify exit overflow interval
- Specifying types of OSPF Syslog messages to log
- Displaying OSPF information
- Displaying general OSPF configuration information
- Displaying CPU utilization statistics
- Displaying OSPF area information
- Displaying OSPF neighbor information
- Displaying OSPF interface information
- Displaying OSPF route information
- Displaying OSPF external link state information
- Displaying OSPF link state information
- Displaying the data in an LSA
- Displaying OSPF virtual neighbor information
- Displaying OSPF virtual link information
- Displaying OSPF ABR and ASBR information
- Displaying OSPF trap status
- Configuring OSPFv3
- Overview
- Differences between OSPFv2 and OSPFv3
- Link state advertisement types for OSPFv3
- Configuring OSPFv3
- Enabling OSPFv3
- Assigning OSPFv3 areas
- Assigning interfaces to an area
- Changing the reference bandwidth for the cost on OSPFv3 interfaces
- Redistributing routes into OSPFv3
- Filtering OSPFv3 routes
- Configuring default route origination
- Modifying Shortest Path First timers
- Modifying administrative distance
- Configuring the OSPFv3 LSA pacing interval
- Modifying exit overflow interval
- Modifying external link state database limit
- Modifying OSPFv3 interface defaults
- Disabling or re-enabling event logging
- IPsec for OSPFv3
- Configuring IPsec for OSPFv3
- IPsec examples
- Displaying OSPFv3 information
- Configuring BGP4 (IPv4)
- Overview of BGP4
- Implementation of BGP4
- Configuring BGP4
- Enabling and disabling BGP4
- Entering and exiting the address family configuration level
- Aggregating routes advertised to BGP4 neighbors
- Configuring the device to always compare Multi-Exit Discriminators
- Disabling or re-enabling comparison of the AS-Path length
- Redistributing IBGP routes
- Enabling or disabling comparison of device IDs
- Four-byte Autonomous System Numbers (AS4)
- Specifying a maximum AS path length
- BGP4 max-as error messages
- Configuring route flap dampening
- Originating the default route
- Changing the default local preference
- Changing the default metric used for redistribution
- Changing the default metric used for route cost
- Changing administrative distances
- Requiring the first AS to be the neighbor AS
- Setting the local AS number
- Configuring BGP4 multipath load sharing
- Configuring paths without MEDs as the least favorable
- Configuring BGP4 neighbors
- Specifying a list of networks to advertise
- Using the IP default route as a valid next-hop for a BGP4 route
- Enabling next-hop recursion
- Modifying redistribution parameters
- Using a table map to set the tag value
- Changing the Keep Alive Time and Hold Time
- Changing the BGP4 next-hop update timer
- Changing the device ID
- Adding a loopback interface
- Changing the maximum number of paths for BGP4 load sharing
- Filtering
- Filtering AS-paths
- Filtering communities
- Defining and applying IP prefix lists
- Defining neighbor distribute lists
- Defining route maps
- Dynamic route filter update
- Configuring route flap dampening
- Updating route information and resetting a neighbor session
- Clearing traffic counters
- Clearing route flap dampening statistics
- Removing route flap dampening
- Clearing diagnostic buffers
- Configuring BGP4 null0 routing
- Displaying BGP4 information
- Displaying summary BGP4 information
- Displaying the active BGP4 configuration
- Displaying summary neighbor information
- Displaying BGP4 neighbor information
- Displaying summary route information
- Displaying the BGP4 route table
- Displaying BGP4 route-attribute entries
- Displaying the routes BGP4 has placed in the IP route table
- Displaying route flap dampening statistics
- Displaying the active route map configuration
- Displaying AS4 details
- Configuring BGP4+
- Address family configuration level
- Configuring BGP4+
- Clearing BGP4+ information
- Displaying BGP4+ information
- Displaying the BGP4+ route table
- Displaying BGP4+ route information
- Displaying BGP4+ route-attribute entries
- Displaying the BGP4+ running configuration
- Displaying dampened BGP4+ paths
- Displaying filtered-out BGP4+ routes
- Displaying route flap dampening statistics
- Displaying BGP4+ neighbor information
- Displaying BGP4+ summary