Usb board sis commands – Extron Electronics SMX System User Guide User Manual
Page 58
SMX System MultiMatrix Switcher • SIS Configuration and Control
52
Command
ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
Commands Specific to SMX USB Boards
Port Emulation for Outputs
Set port emulation for all
outputs
E
E
X
3)
*
X(
*USBC
}
X3)
UsbcE0*
X(
]
Enable or disable port emulation
for all outputs.
Set port emulation for output
pairs
E
E
X3)
*
X#
*
X(
USBC
} X3)
UsbcE
X#
*
X(
]
Enable or disable port emulation
for output
X#
.
View port emulation status for
outputs
E
E
X3)
*
X#
USBC
}
X(
]
X3)
UsbcE
X#
*
X(]
Verbose mode 2 and 3
View port emulation status for
all outputs
E
E
X3)
*USBC
}
X(
1
X(
2
X(
3
...
X(
n
]
X3)
UsbcE*
X(
1
X(
2
...
X(
n
]
Verbose mode 2 and 3
Signal Status
View input signal status
E
I
X3)
*
X!
USBC
}
X(]
X3)
UsbcI
X!
*
X(]
Verbose mode 2 and 3
View all input signal status
E
I
X3)
*USBC
}
X(
1
X(
2
X(
3
...
X(
n
]
X3)
UsbcI*
X(
1
X(
2
X(
3
...
X(
n
]
Verbose mode 2 and 3
View output signal status
E
O
X3)
*
X#
USBC
}
X2)]
X3)
UsbcO
X#
*
X2)]
Verbose mode 2 and 3
View all output signal status
E
O
X3)
*USBC
}
X2)
1
X2)
2
X2)
3
...
X2)
n
]
X3)
UsbcO*
X2)
1
X2)
2
X2)
3
...
X2)
n
]
Verbose mode 2 and 3
Commands Specific to SMX HDMI and DVI Pro Boards
HDCP Status
NOTE:
If the source requires HDCP authentication, ensure that HDCP authorization is set to On (the default).
HDCP Authorization On
E
E
X3)
*
X!
*1HDCP
}
X3)
HdcpE
X!
*1
]
Turn HDCP authorization on for
input
X!
(default).
HDCP Authorization Off
E
E
X3)
*
X!
*0HDCP
}
X3)
HdcpE
X!
*0
]
Turn HDCP authorization on for
input
X!
.
Query HDCP encryption
status
E
E
X3)
*
X!
HDCP
}
X(]
X3)
HdcpE
X!
*
X(]
View HDCP authorization status for
input
X!
.
Verbose mode 2 and 3
NOTES:
X!
= Input number
01
- <
maximum number of inputs
>
X#
= Output number
01
-
04
X(
= On or off status
0
= Off
or disabled
1
= On or enabled
X2)
= Output connection status
0 = No active connection on A or B
1 = 1st (A) port is connected but the 2nd (B) port is not connected
2 = 1st (A) port is not connected but the 2nd (B) port is connected
3 = Active connection on both A and B
X3)
= Slot number
01
-
10
0 = Hard coded, representing all outputs