Extron Electronics SMX System User Guide User Manual
Page 55
SMX System MultiMatrix Switcher • SIS Configuration and Control
49
Command
ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
Commands Specific to SMX SDI/HD-SDI Boards
Output Re-clocking Per Slot
Set output reclocker per slot
X3)
*
X#
*
X1*
=
Rte
X3)
*
X#
*
X1*
]
Read reclocker
X3)
*
X#
=
X1*]
List DSVP (Digital Sync Validation Processing)
DSVP for VGA and RGBHV
List individual sync (DVSP)
X3)
*
X!
LS
X1%
H
,
X1%
V
]
X3)
FRQ
X!
1
,
X1%
H
,
X1%
V
]
Listed as Horizontal, Vertical.
Verbose mode 2 or 3
NOTE:
Unit responds 0000.00, 0000.00 if no connection or an error is found.
List all input sync (DVSP)
X3)
*0LS
X1(
1
X1(
2
...
X1(
n
]
X3)
FRQ00*
X1(
1
X1(
2
...
X1(
n
]
Verbose mode 2 or 3
DSVP (Signal Present) for Composite/S-video/DVI/DVI-Pro/HDMI Boards
List all input sync (DVSP)
X3)
*0LS
X1(
1
X1(
2
...
X1(
n
]
X3)
FRQ0*
X1(
1
X1(
2
...
X1(
n
]
Verbose mode 2 or 3
NOTE:
List individual signal present per slot is not available on this board. Unit responds with error E14.
DSVP (Signal Present and Rate/Reclocker) for SDI/HD-SDI Boards
List individual sync (DVSP)/slot
X3)
*
X#
LS
X1)]
X3)
FRQ
X#
*
X1)]
Verbose mode 2 or 3
NOTE:
Unit responds 0000 if no connection, no ties, or an error is found.
List all sync (DVSP)/slot
X3)
*0LS
X1(
1
X1(
2
...
X1(
n
]
X3)
FRQ0*
X1(
1
X1(
2
...
X1(
n
]
Verbose mode 2 or 3
DSVP (Link Present) for Fiber Optic Boards
List all input (DVSP)
X3)
*0LS
X1(
1
X1(
2
...
X1(
n
]
X3)
FRQ0*
X1(
1
X1(
2
...
X1(
n
]
Verbose mode 2 or 3
NOTE:
List individual signal present per slot is not available on this board. Unit responds with error E14.
Fiber Optic Board Status
View Fiber transceiver module
installed
0*
X3)
I
X*
1
X*
2
...
X*
n
]
Inf
X3)
*
X*
1
X*
2
...
X*
n
]
Verbose mode 2 or 3
NOTES:
X!
= Input number
01 - <maximum number of inputs>
X#
= Output Number
01 - <maximum number of outputs>
X*
= Fiber optic transceiver module
0 = no module installed
1 = multimode module
2 = singlemode module
X1)
= Output rate
---- = bypass mode
0000 = no connection (rate mismatch)
nnnn = actual rate
X1%
= Sync frequency
xxx.xx in Hz or kHz
X1*
= Reclocker rates for SDI/HD-SDI board
00 = autodetect (default)
01 = bypass the reclocker
X1(
= Signal status where
0 = no signal at input
1 = signal at input (H sync)
2 = signal at input (V sync)
3 = signal at input (H and V sync) or receive link presence
X3)
= Slot address 01 - 10