Extron Electronics SMX System User Guide - Manual (Page 50)

SMX System MultiMatrix Switcher • SIS Configuration and Control 44
Command ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
Global Presets (All Planes)
Save current ties as a
global preset X1! , Spr X1!] Save the current set of ties
as global preset
X1! .
Recall a global preset X1! . Rpr X1!] Make the global preset X1!
the current configuration.
NOTE: Attempting to recall an unsaved preset will result in a E11 error code.
Plane Presets
Save current ties as a
plane preset X2@ * X1! *0, X2@ Spr X1!] Save the current set of ties
as plane preset
X1! .
Recall a plane preset X2@ * X1! *0. X2@ Rpr X1!] Recall plane preset X1! as
the current configuration.
View Presets (Ties)
NOTE: The G and P commands are case sensitive.
View current video
configuration/plane E G X2@ *0* X# *1VC } X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Vid ] View video configuration.
Vgp X2@ *00 • Out X# • X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Vid ] Verbose mode 2 or 3
View current audio
configuration/plane E G X2@ *0* X# *2VC } X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Aud ] View audio configuration.
Vgp X2@ *00 • Out X# • X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Aud ] Verbose mode 2 or 3
View global presets (video) E G X2@ * X1! * X# *1VC } X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Vid ] View video configuration.
Vgp X2@ * X1! • Out X# • X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Vid ] Verbose mode 2 or 3
View global presets (audio) E G X2@ * X1! * X# *2VC } X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Aud ] View audio configuration.
Vgp X2@ * X1! • Out X# • X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Aud ] Verbose mode 2 or 3
View plane presets (video) E P X2@ * X1! * X# *1VC } X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Vid ] View video configuration.
Vpp X2@ * X1! • Out X# • X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Vid ] Verbose mode 2 or 3
View plane presets (audio) E P X2@ * X1! * X# *2VC } X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Aud ] View audio configuration.
Vpp X2@ * X1! • Out X# • X@ 1 • X@ 2 • X@ 3 • X@ 4 ... X@ 16 • Aud ] Verbose mode 2 or 3
NOTES:
• If a preset is unassigned, then name displayed is [unassigned].
• If a global preset is saved but not yet named, then default name is “Preset X1! , ” ( X1! = preset number).
• Viewing global presets show the ties for the selected plane.
• Viewing plane presets lists only the configuration of that particular plane.
• When viewing outputs, only outputs higher than the one designated display.
Virtual (Multi Plane) Definition
Write virtual plane address EX2( , X2@ 1 * X2@ 2 * X2@ n MP } Mpv X2( , X2@ 1 , X2@ 2 ... X2@ n ] Write virtual plane address.
Read Virtual plane address EX2( MP } X2@ 1 , X2@ 2 ... X2@ n ] Read virtual plane address.
NOTES:
X@ = Input number 01 - <maximum number of inputs>
X# = Output number 01 - <maximum number of outputs>
X1! = Preset number 01 - 32 = global presets
1 - 10 = plane presets
X2@ = Plane number 00 - 15 = 16 planes
X2( = Virtual plane number 90 - 99 = 10 planes