Atmega128(l) – Rainbow Electronics ATmega128L User Manual
Page 311

311
ATmega128(L)
2467B–09/01
Notes:
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at V
CC
= 5V, 10 mA at V
CC
= 3V) under steady state
conditions (non-transient), the following must be observed:
TQFP Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0-A7, should not exceed 100 mA.
3] The sum of all IOL, for ports B0-B3, should not exceed 100 mA.
4] The sum of all IOL, for ports B4-B7, should not exceed 100 mA.
5] The sum of all IOL, for ports C0-C3, should not exceed 100 mA.
6] The sum of all IOL, for ports C4-C7, should not exceed 100 mA.
7] The sum of all IOL, for ports D0-D3 and XTAL2, should not exceed 100 mA.
8] The sum of all IOL, for ports D4-D7, should not exceed 100 mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
conditions (non-transient), the following must be observed:
TQFP Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports A0-A7, should not exceed 100 mA.
3] The sum of all IOH, for ports B0-B3, should not exceed 100 mA.
4] The sum of all IOH, for ports B4-B7, should not exceed 100 mA.
5] The sum of all IOH, for ports C0-C3, should not exceed 100 mA.
6] The sum of all IOH, for ports C4-C7, should not exceed 100 mA.
7] The sum of all IOH, for ports D0-D3 and XTAL2, should not exceed 100 mA.
8] The sum of all IOH, for ports D4-D7, should not exceed 100 mA
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum V
CC
for Power-down is 2.5V.
I
CC
Power Supply Current
Active 4 MHz, V
CC
= 3V
(
ATmega128
L)
TBD
mA
Active 8 MHz, V
CC
= 5V
(
ATmega128
)
TBD
mA
Idle 4 MHz, V
CC
= 3V
(
ATmega128
L)
TBD
mA
Idle 8 MHz, V
CC
= 5V
(
ATmega128
)
TBD
mA
Power-down mode
WDT enabled, V
CC
= 3V
TBD
TBD
µA
WDT disabled, V
CC
= 3V
TBD
TBD
µA
V
ACIO
Analog Comparator
Input Offset Voltage
V
CC
= 5V
V
in
= V
CC
/2
TBD
mV
I
ACLK
Analog Comparator
Input Leakage Current
V
CC
= 5V
V
in
= V
CC
/2
TBD
TBD
nA
t
ACID
Analog Comparator
Initialization Delay
V
CC
= 2.7V
V
CC
= 4.0V
TBD
TBD
ns
t
ACID
Analog Comparator
Propagation Delay
V
CC
= 2.7V
V
CC
= 4.0V
TBD
TBD
ns
T
A
= -40
°C to 85°C, V
CC
= 2.7V to 5.5V (unless otherwise noted)
(Continued)
Symbol
Parameter
Condition
Min
Typ
Max
Units