Comtech EF Data SNM-1000 - Manual (Page 181)

SNM-1000 Node Control Modem Revision 3
Remote Control Operation MN/SNM1000.IOM
A–33
A.9.4 Cause and Subcause Codes Generated By Node
Example
Cause Subcause Name Status Description
0x00 cause_Unknown term_PathOk
0x01 cause_NodeChanBusy term_Busy Called node/channel is busy
0x04 cause_NoCarrier term_FailureRet Carrier lock was never achieved
0x05 cause_CarrierLost term_FailureRet Carrier lock was achieved, but then lost
0x06 cause_ISDNFault term_FailureRet ISDN faults to be defined
0x00-0x0D reserved
0x0E subcause_InvalidRate Invalid data rate for ISDN call
0x0F-0xFF reserved
0x07 cause_ModemProg term_FailureRet General Modem Programming failure
0x00 subcause_Unknown Generic subcause code
0x01 subcause_InvalidOpCode Internal error code
0x02 subcause_OpCodeFault Internal error code
0x03 subcause_InvalidResponseBuffer Internal error code
0x04 subcause_InvalidParm Internal error code
0x05 subcause_InvalidChan Channel number out of range
0x06 subcause_AccessDenied Channel access denied
0x07 subcause_ChannelOffline Channel went offline
0x08 subcause_InvalidRequestBuffer Internal error code
0x09 subcause_InvalidNodeStartupCode Internal error code
0x0A subcause_InvalidNodeDisableOption Internal error code
0x0B subcause_InvalidNodeStatusOption Internal error code
0x0C subcause_InvalidTxFreq Invalid transmit frequency
0x0D subcause_InvalidRxFreq Invalid receive frequency
0x0E subcause_InvalidRate Invalid Modulation ,code rate, data rate selection
0x0F subcause_InvalidPower Invalid power level
0x10 subcause_InvalidTxClock Invalid transmit clock selection
0x11 subcause_ChannelLocked Channel already processing call
0x12 subcause_ModemFault Channel not responding to periodic status request
0x13 subcause_NoCarrier Carrier Not Detected
0x14 subcause_InvalidParmBuffer Internal error code
0x15 subcause_CallNotActive Call not in progress
0x16 subcause_ModemNotPresent Internal error code
0x17 subcause_ModemFaultDetected Modem offline
0x18 subcause_InvalidEncoderType Invalid Encoder Selection
0x19 subcause_InvalidDecoderType Invalid Decoder Selection
0x1A subcause_InvalidBus Channel not defined on specific bus
0x1B subcause_InvalidSweep Invalid demodulator sweep rate range
0x1C subcause_NoBufferAvail Internal error code
0x1D subcause_InvalidDEncoder Invalid differential encoder selection
0x1E subcause_InvalidDDecoder Invalid differential decoder selection
0x1F subcause_ChannelNotInitialized Internal error code
0x20 subcause_ InvalidTransmitMode Invalid Transmit Mode selection
0x21 subcause_ InvalidBuffersize Invalid Modem buffer size
0x22 subcause_ InvalidAupcOption Invalid Aupc Option
0x23 subcause_ InvalidAupcNominalPower Invalid Aupc Nominal Power
0x24 subcause_ InvalidAupcMax Invalid Aupc Max Power
0x25 subcause_ InvalidAupcMin Invalid Aupc Min Power
0x26 subcause_ InvalidAupcSP Invalid Aupc Set Point
0x27 subcause_ InvalidAupcMaxRate Invalid Aupc Max Rate
0x28 subcause_ InvalidLocalAction Invalid Aupc Local Action
0x29 subcause_ InvalidRemoteAction Invalid Aupc Remote Action
0x30 subcause_ InvalidModemType Internal error code
0x31 subcause_ InvalidFramingType Invalid Framing Selection
0x18 cause_IncompVoiceCap term_FailureRet Attempt to mix G.728 + G.729 voice circuit
0x19 cause_IncompPhNum term_FailureRet Calling side PPTREQ # not equal PTTASSIGN #
0x1A cause_InvalidVfduCmd term_FailureRet VFDU Card rejected DAC Command
0x03 cause_NoAnsTimer term_Normal No answer timer expired without going offhook