Rockwell Automation 193-EC4 EC4 Current Monitoring Relay User Manual - Manual (Page 58)

Rockwell Automation Publication 193-UM011A-EN-P - September 2010 59
Programmable Parameters Chapter 5
Table 16 - Parameter Group Listing
Monitor Params (All
Read-Only)
Advanced Setup Reset / Lock DeviceNet Setup Output Setup DeviceLogix
1
L1 Current
(in Amps)
24
Trip Enable
(Change bit masking)
26
Trip Reset
(Ready/Reset
Trip)
55
AutoBaudEnable
(Enable/Disable)
65
OutA Pr FltState
(Go to FltValue/
Ignore Fault)
79
Comm Override
(Enabled/
Disabled)
2
L2 Current
(in Amps)
25 Warning Enable 53
Program Lock
(Unlock/Lock)
56
NonVol Baud
Rate (125K,
250K, 500K
Baud)
66
OutA Pr FltValue
(Open/Closed)
80
Network Override
(Enabled/
Disabled)
3
L3 Current
(in Amps)
35
GF Inhibit Time
(0…250 s)
54
Set To
Defaults
(Ready/Reset
Defaults)
58
COS Mask (Bit
Masking)
67
OutA Dn FltState
(Go to FltValue/
Ignore Fault)
81
Net Outputs
(Read-Only)
10
GF-Current
(in Amps)
36 GF Trip Delay (0…25 s) 103
Test Enable
(Enable/
Disable)
59
Output Assembly
(0…140)
68
OutA Dn FltValue
(Open/Closed)
82
Net Out COS
Mask (Bit mask)
14 Trip Status 37
GF Trip Level
(0.02…5 A)
104
Clear Queue
(Ready/ Clear)
60
Input Assembly
(0…184)
69
OutA Dn IdlState
(Go to IdlValue/
Hold Last State)
15 Warning Status 38
GF Warn Level
(0.02…5 A)
61
Assy Word0
Param (0…130)
70
OutA Dn IdlValue
(Open/Closed)
16 Trip Log 0 83
IN1 Assignment
(Normal, Trip Reset,
Remote Trip, L1 Loss
Arm, L2 Loss Arm,
L3 Loss Arm, L1L2 Loss
Arm, L2L3 Loss Arm,
L1L3 Loss Arm, L1L2L3
Loss Arm)
62
Assy Word1
Param (0…130)
71
OutB Pr FltState
(Go to FltValue/
Ignore Fault)
17 Trip Log 1 84 IN2 Assignment 63
Assy Word2
Param (0…130)
72
OutB Pr FltValue
(Open/Closed)
18 Trip Log 2 85 IN3 Assignment 64
Assy Word3
Param (0…130)
73
OutB Dn FltState
(Go to FltValue/
Ignore Fault)
19 Trip Log 3 86 IN4 Assignment 74
OutB Dn FltValue
(Open/Closed)
20 Trip Log 4 89
GF Trip Inhibi
(Enable/Disable)
75
OutB Dn IdlState
(Go to IdlValue/
Hold Last State)
21 Device Status 101
PM – # Starts
(0…65535)
76
OutB Dn IdlValue
(Open/Closed)
22 Firmware 102 Oper. Hours (0…65535)
23
Device
Configutation
105
GF Warning Delay
(0…25 s)
90 Warning Log 0 106
GF Sensing Range
(20…100 mA,
100…500 mA,
0.2…1 A, 1…5 A)
91 Warning Log 1 107
UC Inhibit Time
(0…250 s)
92 Warning Log 2 108 L1 UC Trip Level
93 Warning Log 3 109
L1 UC Trip Delay
(0.1…25 s)
94 Warning Log 4 110 L1 UC Warn Level
95 Elapsed Time 111 L2 UC Trip Level
96 Starts Counter 112
L2 UC Trip Delay
(0.1…25 s)
113 L2 UC Warn Level
114 L3 UC Trip Level