HYDAC CS 1000 User Manual

Cs1000 series contaminationsensor

Text mode
Original mode

CS1000 series
ContaminationSensor

Operating and maintenance instructions

English (Translation of original)

Valid from firmware version V 2.20

Documentation no.: 3247149n

Table of contents

Document Outline

Trademarks
Exclusion of liability
Content
Preface
- Technical Support
- Product modification
- Warranty
- Using the documentation
General safety guidelines
- Obligations and liability
- Explanation of symbols and warnings
  - Basic symbols
- Intended use
- Improper use
- Informal safety precautions
- Training and instruction of personnel
New features — instruction modifications
Storing ContaminationSensor
- Storage conditions
Interpreting the type label
Checking the scope of delivery
CS1000 Features
- CS1000 Restrictions on use
- CS1x1x dimensions (without display)
- CS1x2x dimensions (with display)
- Hydraulic connection types
  - Pipe or hose connection (Type CS1xxx-x-x-x-x-0/-xxx)
  - Flange connection type (Type CS1xxx-x-x-x-x-1/-xxx)
- Fastening / mounting the CS1000
- Display rotatable/Adjustable As Needed
- CS1000 hydraulic installation
- Electrical connection of the CS1000
CS measurement modes
- Mode M1: Continuous measurement
- Mode M2: Continuous measurement and switching
- Mode M3: Filter to cleanliness class and stop
- Mode M4: Filter to continuously monitor cleanliness class
- Mode "SINGLE" individual measurement
Operating the CS1000 per keyboard (Only CS1x2x)
- Measurement categories
- Service categories
- Activating/deactivating key lock
- Modes and menus
  - Power Up menu
  - Measuring Menu
Display — Select display after switching on the sensor
ANA.OUT
- Measuring menu (CS13xx)
Display — Select displayed measurement category after switching on the sensor
MODE – Configure measuring mode
ANA.OUT
Overview of menu structure
- Menu CS 12xx (ISO 4406:1999 and SAE)
- Menu CS 13xx (ISO 4406:1987 and NAS)
Using switching output
- Mode M1: Continuous measurement
- Mode M2: Continuous measurement and switching
- Mode M3: Filter to cleanliness class and stop
- Mode M4: Filter to continuously monitor cleanliness class
- "SINGLE" measurement mode
- Setting limit values
Analog Output (ANAOUT)
- SAE classes acc. to AS 4059
HDA.SAE Signal 1/2/3/4
HDA Status Signal 5
- ISO Code acc. to 4406:1999
HDA.ISO Signal 1/2/3/4
HDA Status Signal 5
- ISO code signal acc. to 4406:1987 (CS 13xx only)
HDA.ISO Signal 1/2/3/4
HDA Status Signal 5
- NAS 1638 - National Aerospace Standard (Only CS 13xx)
HDA Signal 1/2/3/4
HDA Status Signal 5
- Fluid temperature (TEMP)
Status messages
- Status LED / display
- Error
- Exception errors
- Analog output error signals
  - Analog signal for HDA 5500
HDA status signal 5 table
Connecting CSI-D-5 (Condition Sensor Interface)
- CSI-D-5 Connection overview
CS1000 in RS-485 bus
Taking the CS1000 out of operation
- Disposing of CS1000
Spare parts and accessories
Cleanliness classes - brief overview
- Cleanliness class - ISO 4406:1999
  - Table - ISO 4406
  - Overview of modifications - ISO4406:1987 vs. ISO4406:1999
- Cleanliness class - SAE AS 4059
  - Table - SAE AS 4059
  - Definition acc. to SAE
Particle count (absolute) larger than a defined particle size
Specifying a cleanliness class for each particle size
Specify highest measured cleanliness class
- Cleanliness Class - NAS 1638
Checking/resetting factory default settings
- Power Up menu
- Measuring menu
Technical data
Recalibration
Customer service
Model code