beautypg.com

1 ball assignments, Ball assignments, Table 3-1 – AMD Geode SC1201 User Manual

Page 27: Signal definitions legend, Section 3.1 "ball assignments": pro

background image

AMD Geode™ SC1200/SC1201 Processor Data Book

27

Signal Definitions

32579B

3.1

Ball Assignments

The SC1200/SC1201 processor is highly configurable as
illustrated in Figure 3-1 on page 25. Strap options and reg-
ister programming are used to set various modes of opera-
tion and specific signals on specific balls. This section
describes which signals are available on which balls and
provides configuration information:

Figure 3-2 on page 28: Illustrates the BGU481 ball

assignments.

Table 3-2 on page 29: Lists signals according to ball

number. Power Rail, Signal Type, Buffer Type and,
where relevant, Pull-Up or Pull-Down resistors are indi-
cated for each ball in this table. For multiplexed balls, the
necessary configuration for each signal is listed as well.

Table 3-3 on page 40: Quick reference signal list sorted

alphabetically - listing all signal names and ball
numbers.

The tables in this chapter use several common abbrevia-
tions. Table 3-1 lists the mnemonics and their meanings

Notes:

1)

For each GPIO signal, there is an optional pull-up
resistor on the relevant ball. After system reset, the
pull-up is present.

This pull-up resistor can be disabled via registers in the
Core Logic module. The configuration is without regard to
the selected ball function (except for GPIO12, GPIO13,
and GPIO16). Alternate functions for GPIO12, GPIO13,
and GPIO16 control pull-up resistors.

For more information, see Section 6.4.1 "Bridge,
GPIO, and LPC Registers - Function 0" on page 190.

2)

Configuration settings listed in this table are with
regard to the Pin Multiplexing Register (PMR). See
Section 4.2 "Pin Multiplexing, Interrupt Selection, and
Base Address Registers" on page 72
for a detailed
description of this register.

Table 3-1. Signal Definitions Legend

Mnemonic

Definition

A

Analog

AV

SS

Ground ball: Analog

AV

CC

Power ball: Analog

GCB

General Configuration Block registers.
Refer to Section 4.0 "General Configura-
tion Block" on page 71
.

Location of the General Configuration
Block cannot be determined by software.
See AMD Geode™ SC1200/SC1201
Processor Specification Update docu-
ment.

I

Input ball

I/O

Bidirectional ball

MCR[x]

Miscellaneous Configuration Register
Bit x: A register, located in the GCB.
Refer to Section 4.1 "Configuration
Block Addresses" on page 71
for further
details.

O

Output ball

OD

Open-drain

PD

Pull-down (K

Ω)

PMR[x]

Pin Multiplexing Register Bit x: A regis-
ter, located in the GCB, used to config-
ure balls with multiple functions. Refer to
Section 4.1 "Configuration Block
Addresses" on page 71 f
or further
details.

PU

Pull-up (K

Ω)

TS

TRI-STATE

V

CORE

Power ball: 1.2V

V

IO

Power ball: 3.3V

V

SS

Ground ball

#

The # symbol in a signal name indicates
that the active or asserted state occurs
when the signal is at a low voltage level.
Otherwise, the signal is asserted when
at a high voltage level.

/

A / in a signal name indicates both func-
tions are always enabled (i.e., cycle mul-
tiplexed).

+

A + in signal name indicates the function
is available on the ball, but that either
strapping options or register program-
ming is required to select the desired
function.

This manual is related to the following products: