beautypg.com

2 smi status and acpi registers - function 1, Table 6-32, Table 6-32) – AMD Geode SC1201 User Manual

Page 236

background image

236

AMD Geode™ SC1200/SC1201 Processor Data Book

Core Logic Module - SMI Status and ACPI Registers - Function 1

32579B

6.4.2

SMI Status and ACPI Registers - Function 1

The register space designated as Function 1 (F1) is used
to configure the PCI portion of support hardware for the
SMI Status and ACPI Support registers. The bit formats for
the PCI Header registers are given in Table 6-32.

Located in the PCI Header registers of F1 are two Base
Address Registers (F1BARx) used for pointing to the regis-
ter spaces designated for SMI status and ACPI support,
described later in this section.

Table 6-32. F1: PCI Header Registers for SMI Status and ACPI Support

Bit

Description

Index 00h-01h

Vendor Identification Register (RO)

Reset Value: 100Bh

Index 02h-03h

Device Identification Register (RO)

Reset Value: 0501h

Index 04h-05h

PCI Command Register (R/W)

Reset Value: 0000h

15:1

Reserved. (Read Only)

0

I/O Space. Allow the Core Logic module to respond to I/O cycles from the PCI bus.

0: Disable.

1: Enable.

This bit must be enabled to access I/O offsets through F1BAR0 and F1BAR1 (see F1 Index 10h and 40h).

Index 06h-07h

PCI Status Register (RO)

Reset Value: 0280h

Index 08h

Device Revision ID Register (RO)

Reset Value: 00h

Index 09h-0Bh

PCI Class Code Register (RO)

Reset Value: 068000h

Index 0Ch

PCI Cache Line Size Register (RO)

Reset Value: 00h

Index 0Dh

PCI Latency Timer Register (RO)

Reset Value: 00h

Index 0Eh

PCI Header Type (RO)

Reset Value: 00h

Index 0Fh

PCI BIST Register (RO)

Reset Value: 00h

Index 10h-13h

Base Address Register 0 - F1BAR0 (R/W)

Reset Value: 00000001h

This register allows access to I/O mapped SMI status related registers. Bits [7:0] are read only (0000 0001), indicating a 256-byte I/O
address range. Refer to Table 6-33 on page 237 for bit formats and reset values of the SMI status registers.

31:8

SMI Status Base Address.

7:0

Address Range. (Read Only)

Index 14h-2Bh

Reserved

Reset Value: 00h

Index 2Ch-2Dh

Subsystem Vendor ID (RO)

Reset Value: 100Bh

Index 2Eh-2Fh

Subsystem ID (RO)

Reset Value: 0501h

Index 30h-3Fh

Reserved

Reset Value: 00h

Index 40h-43h

Base Address Register 1 - F1BAR1 (R/W)

Reset Value: 00000001h

This register allows access to I/O mapped ACPI related registers. Bits [7:0] are read only (0000 0001), indicating a 256 byte address
range. Refer to Table 6-34 on page 247 for bit formats and reset values of the ACPI registers.

Note:

This Base Address register moved from its normal PCI Header Space (F1 Index 14h) to prevent plug and play software from
relocating it after an FACP table is built.

31:8

ACPI Base Address.

7:1

Address Range. (Read Only)

0

Enable. (Write Only) This bit must be set to 1 to enable access to ACPI Support Registers.

Index 44h-FFh

Reserved

Reset Value: 00h

This manual is related to the following products: