beautypg.com

AMD Geode SC1201 User Manual

Page 258

background image

258

AMD Geode™ SC1200/SC1201 Processor Data Book

Core Logic Module - IDE Controller Registers - Function 2

32579B

Index 44h-47h

Channel 0 Drive 0 DMA Control Register (R/W)

Reset Value: 00077771h

The structure of this register depends on the value of bit 20.

If bit 20 = 0, Multiword DMA

Settings for a Fast-PCI clock frequency of 33.3 MHz:

Multiword DMA Mode 0 = 00077771h

Multiword DMA Mode 1 = 00012121h

Multiword DMA Mode 2 = 00002020h

Settings for a Fast-PCI clock frequency of 66.7 MHz:

Multiword DMA Mode 0 = 000FFFF3h

Multiword DMA Mode 1 = 00035352h

Multiword DMA Mode 2 = 00015151h

Note:

All references to “cycle” in the following bit descriptions are to a Fast-PCI clock cycle.

31

PIO Mode Format. This bit sets the PIO mode format for all channels and drives. Bit 31 of Offsets 2Ch, 34h, and 3Ch are R/
W, but have no function so are defined as reserved.

0: Format 0.

1

Format 1.

30:21

Reserved. Must be set to 0.

20

DMA Select. Selects type of DMA operation. 0: Multiword DMA

19:16

tKR. IDE_IOR# recovery time (4-bit) (value + 1 cycle).

15:12

tDR. IDE_IOR# pulse width (value + 1 cycle).

11:8

tKW. IDE_IOW# recovery time (4-bit) (value + 1 cycle).

7:4

tDW. IDE_IOW# pulse width (value + 1 cycle).

3:0

tM. IDE_CS[1:0]# to IDE_IOR#/IOW# setup; IDE_CS[1:0]# setup to IDE_DACK0#/DACK1#.

If bit 20 = 1, UltraDMA

Settings for a Fast-PCI clock frequency of 33.3 MHz:

UltraDMA Mode 0 = 00921250h

UltraDMA Mode 1 = 00911140h

UltraDMA Mode 2 = 00911030h

Settings for a Fast-PCI clock frequency of 66.7 MHz:

UltraDMA Mode 0 = 009436A1h

UltraDMA Mode 1 = 00933481h

UltraDMA Mode 2 = 00923261h

Note:

All references to “cycle” in the following bit descriptions are to a Fast-PCI clock cycle.

31

PIO Mode Format. This bit sets the PIO mode format for all channels and drives. Bit 31 of Offsets 2Ch, 34h, and 3Ch are R/
W, but have no function so are defined as reserved.

0: Format 0.

1: Format 1.

30:24

Reserved. Must be set to 0.

23:21

BSIZE. Input buffer threshold.

20

DMA Select. Selects type of DMA operation. 1: UltraDMA.

19:16

tCRC. CRC setup UDMA in IDE_DACK# (value + 1 cycle) (for host terminate CRC setup = tMLI + tSS).

15:12

tSS. UDMA out (value + 1 cycle).

11:8

tCYC. Data setup and cycle time UDMA out (value + 2 cycles).

7:4

tRP. Ready to pause time (value + 1 cycle). Note: tRFS + 1 tRP on next clock.

3:0

tACK. IDE_CS[1:0]# setup to IDE_DACK0#/DACK1# (value + 1 cycle).

Table 6-35. F2: PCI Header/Channels 0 and 1 Registers for IDE Controller Configuration (Continued)

Bit

Description

This manual is related to the following products: