Watlow EZ-ZONE RM Limit Module Rev C - Manual (Page 51)

Watlow EZ-ZONE ® RML Module • 48 • Chapter 4 Setup Page
RM Limit Module • Setup Page
Display
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter
ID
Data
Type
&
Read/
Write
[`S2;A]
[ SZ.A] Limit (1 to 12)
Source Zone A
Set the zone of the function
selected above.
0 or 16 0 - - - - 0x70 (112)
1 to 0xC
(12)
0x11 (17)
- - - - 12017 uint
RWES
[`lCr]
[ LCr] Limit (1 to 12)
Limit Clear
Clear the specified limit if
limit condition no longer
exists.
[`Clr] Clear (129)
[ignr] Ignore (204)
Ignore 1516
[offset 30]
0x70 (112)
1 to 0xC
(12)
0x0E (14)
- - - - 12014 uint
R
[`l;st]
[ L.St] Limit (1 to 12)
Limit Status
Current state of limit.
[fail] Fail (32)
[safe] Safe (1667)
- - - - 1500
[offset 30]
0x70 (112)
1 to 0xC
(12)
6
- - - - 12013 uint
R
[otpt]
[`Set]
Output Menu
[``Fn]
[ Fn] Output (1 to 4 and 7 - 10)
Function
Select what function will
drive this output.
Note:
Output 8 is set by default
(factory settings) to mod-
ule limit
[`oFF] Off (62)
[ALM] Alarm (6)
[`CPE] Compare (230)
[`Ctr] Counter (231)
[`dio] Digital I/O (1142)
[`FUn] Function Key (1001)
[`lnr] Linearization (238)
[`LgC] Logic (239)
[mat] Math (240)
[tMr] Timer (244)
[`uAr] Variable (245)
[m;li] Module Limit (1696)
[LiM] Limit (126)
off 1858
[offset 30] 0x6A
(106)
1 to 0xA
(10)
5
96 6005 uint
RWES
[``Fi]
[ Fi] Output (1 to 4 and 7 - 10)
Function Instance
Set the instance of the
function selected above.
1 to 24 1 1860
[offset 30] 0x6A
(106)
1 to 0xA
(10)
6
- - - - 6006 uint
RWES
[`S2;A]
[ SZ.A] Output (1 to 4 and 7 - 10)
Source Zone A
Set the instance of the
function selected above.
1 to 16 0 1872
[offset 30] 0x6A
(106)
1 to 0xA
(10)
0xC (12)
- - - - 6012 uint
RWES
[`o;Ct]
[ o.Ct] Output (1 to 4 and 7 - 10)
Control
Set the output control type.
This parameter is only
used with PID control, but
can be set anytime.
[`Ftb] Fixed Time Base (34)
[`utb] Variable Time Base
(103)
Fixed
Time
Base
1852
[offset 30] 0x6A
(106)
1 to (12)
2
- - - - 6002 uint
RWES
[`o;tb]
[ o.tb] Output (1 to 4 and 7 - 10)
Time Base
Set the time base for fixed-
time-base control.
0.1 to 60.0 seconds (solid-
state relay or switched dc)
5.0 to 60.0 seconds (mechani-
cal relay or no-arc power
control)
0.1 sec.
[SSR &
sw dc]
20.0 sec.
[mech,
relay, no-
arc]
1854
[offset 30] 0x6A
(106)
1 to (12)
3
- - - - 6003 float
RWES
Note: Some values will be rounded off to fit in the four-character display .
Full values can be read with other interfaces .
If there is only one instance of a menu, no submenus will appear .
R: Read
W: Write
E: EEPROM
S: User
Set