Extron Electronics MLC 226 IP Series Installation - Manual (Page 102)

SIS ™ Programming and Control, cont’d
MLC 226 IP Series • SIS Programming and Control 5-24
PRELIMINAR
Y
Command/r
esponse table for SIS commands (continued)
Command
ASCII (T
elnet)
(host to switcher)
URL Encoded (W
eb)
(host to switcher)
Response (switcher to host)
Additional description
Clear administrator passwor
d
24
E
• CA
}
W%20 CA
]
Ipa•
]
Clear/r
emove all passwor
ds (administrator
and user).
N
A
user password cannot be assigned if an administrator password does not exist. Also, if the administrator password is clear
ed, the user password is also clear
ed.
Read administrator passwor
d
E
CA
}
WCA
|
X4!
]
Set user passwor
d
14, 24
E
X3#
CU
}
W
X3#
CU
|
Ipu•
X4!
]
Set the user passwor
d (
X3#
is 4 to 12
alphanumeric characters). The passwor
d is
case sensitive. Special characters (spaces, symbols) ar
e not allowed.
X4!
=
Passwor
d
to display on scr
een.
N
A
user password cannot be assigned if an administrator password does not exist. Also, if the administrator password is clear
ed
, the user password is also clear
ed.
Clear user passwor
d
24
E
• CU
}
W%20CU
|
Ipu•
]
This clears the user passwor
d only
.
Read user passwor
d
E
CU
}
WCU
|
X4!
]
Remapping port designations
For security r
easons the network administrator may wish to assign new/dif
fer
ent port numbers to the contr
oller
’s T
elnet, W
eb br
owser
, and dir
ect access ports or to disable
one or mor
e ports. T
ypically T
elnet uses port 23, W
eb access is via port 80 (HTTP), and dir
ect access is via port 2001.
C
Do
no
t set two or mor
e ports to the same port number
. Setting two ports to the same number could cause networking confl
icts and will also r
esult in an E13 (invalid
parameter) err
or
.
N
If you r
emap a port, you must set the port number to 1024 or higher
, unless you r
eset the port to the default number or disabl
e the port by setting it to 0.
Set the T
elnet port map
24
E
{port#}MT
}
W{port#}MT
|
Pmt {port#}
]
Select a number for the port that will not confl
ict with any other ports.
Reset the T
elnet port map
24
E
23MT
}
W23MT
|
Pmt 00023
]
This r
esets the T
elnet port to port 23.
Disable the T
elnet port map
24
E
0MT
}
W0MT
|
Pmt 00000
]
Setting the port number to 0 disables the port.
Read the T
elnet port map
E
MT
}
WMT
|
{port#}
]
Set the W
eb port map
24
E
{port#}MH
}
W{port#}MH
|
Pmh {port#}
]
Reset the W
eb port map
24
E
80MH
}
W80MH
|
Pmh 00080
]
This r
esets the W
eb port to port 80.
Disable the W
eb port
24
E
0MH
}
W0MH
|
Pmh 00000
]
Read the W
eb port map
E
MH
}
WMH
|
{port#}
]
Set the Dir
ect
Access port map
24
E
{port#}MD
}
W{port#}MD
|
Pmd {port#}
]
Reset the Dir
ect
Access port
map
24
E
2001MD
}
W2001MD
|
Pmd 02001
]
This r
esets the dir
ect access port to port
2001.
Disable the Dir
ect
Access port
24
E
0MD
}
W0MD
|
Pmd 00000
]
Read the Dir
ect
Access port map
E
MD
}
WMD
|
{port#}
]