Toshiba STRATA CIX User Manual
Page 67
Telephone Button Programming
300 Series Programs
Strata CIX/CTX Telephone Button Programming 11/04
1-63
T
e
le
phon
e Butt
on
Pr
og
ramm
ing
310-
01~03
Day1/Day2/Night
Destination Type
FB01
~
FB03
, n,
Spkr
n =
1.
No Data (default)
2.
Dialing Digits
3.
DISA
4.
Built-in Modem
5.
Night Bell
Select Destination Type for each.
•
No Data ñ no destination will ring when the line rings into the
system.
•
Dialing Digits ñ assigns the line to ring the directory number or
access code defined in the ìDestination Digitsî assignment
•
DISA ñ assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
•
Modem ñ assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
•
Night Bell ñ Assigns the line to cause the night relay to pulse
(one-sec. close/3-sec. open)
Day1/Day2/Night
Destination Digits
n1,
Hold
n1 =
Up to 32 digits
Enter Destination, Directory Number or Access Codes for each, only
if Dialing Digits is selected as Destination Type.
•
If Dialing Digits is the Destination Type, enter the Directory
Number that the line should ring.If the line should ring over
external page, enter #31xx, where xx is the external Page group
number.
•
If the default page access code #31 was changed, use the new
page access code as the leading digits.
•
Line access codes and network routing numbers can also be
entered to route incoming calls back out to a public or private
network number.
310-04
MOH Source
FB04
, n,
Hold
,
Hold
n =
1.
Silence
2.
External 1 (default)
3.
External 2
4.
External 3
5.
External 4
6.
External 5
7.
External 6
8.
External 7
9.
External 8
10. External 9
11. External 10
12. External 11
13. External 12
14. External 13
15. External 14
16. External 15
Select the MOH source for Analog DIT Trunk. The Scroll key must be
used to select MOH sources indicated by 10 or higher.
311
DISA Security Codes
311
,
Hold
This command assigns DISA parameters.
311-01
DISA Enabled
FB01
, n,
Hold
n =
1.
Enable
2.
Disable
(default)
Enable DISA security code.
311-02
DISA Code
FB02
, n,
Hold
n =
Up to 15 digits
Enter DISA security code.
311-03
Response Timer
FB03
, n,
Hold
n =
0~30
(default = 5)
Enter the time, in seconds, for Strata CTX to respond to a call.
311-04
Idle Timer
FB04
, n,
Hold, Hold
n =
0~60
(default = 10)
Enter the time in seconds to wait for idle DTMF.
311-05
Tie Line Access
FB05
, n,
Hold, Hold
n =
1.
Enable
2. Disable (default)
Enable this feature to allow DISA callers to access Tie lines when
they call into the system.
312
DID Number Delete
312
,
Hold
This command deletes DID Number.
312-00
ILG Number
n =
1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
(default = 0)
ILG Number.
Table 1-28
Programs 303~315
(continued)
Button
Sequence
Value(s)
Summary