Toshiba STRATA CIX User Manual
Page 59
Telephone Button Programming
300 Series Programs
Strata CIX/CTX Telephone Button Programming 11/04
1-55
T
e
le
phon
e Butt
on
Pr
og
ramm
ing
302-06
Trunk ID Number
FB06
, n,
Hold
n =
0~126
(default = 0)
An identifier must be used as part of the addressing when an ìexplicitî
identified is used to communicate with the PSTN which channel on
which link is used for the given call. This identifier is assigned by the
connected PSTN.
302-07
D Ch Position
FB07
, n,
Hold
n =
1~24
(default = 24)
PRI includes a 64-kbps D-channel (for transfer of signal information).
Select the channel position to be used for D channel signaling.
Note
This field is used only when the span interface speed is 1.5M.
If the span interface speed is 2M the value is fixed at 16.
302-
08~13
Bearer Services:
•
Speech
•
3.1 KHz Audio
•
7 KHz Audio
•
Unrestr. 64K
•
Unrestr. 56K
•
Unrestr. 2x64K
FB08
~
FB13
, n,
Spkr
,
n1,
Hold
n =
1.
Enable
2.
Disable
Enable the Bearer Capabilities allowed for this PRI Trunk channel
group.
n1 =
1.
Channel Number
2.
Slot Map
Select the Channel Method (map) to identify the channels.
Note
In North America, only Channel Number map is used
(Channel Number).
302-
14~18
Bearer Services:
•
Unrestr. 384K
•
Unrestr. 1536K
•
Unrestr. 1920K
•
Restr. Digital
•
Video
FB14
~
FB18
, n,
Spkr
,
n1,
Hold
n =
1.
Enable
2.
Disable (default)
The Bearer Capabilities (384k Unrestricted(H0), 1536k
Unrestricted(H11), 1920k Unrestricted, Restricted Digital Info, Trunk
Video, and Unrestricted Multirate) are not used and should remain
disabled.
n1 =
1.
Channel Number B
2.
Channel Number H
3.
Slot Map B
4.
Slot Map H
Select the Channel Method (map) to identify the channels.
Note
In North America, only Channel Number B map is used.
302-19
Bearer Service
Multirate Unrestricted
FB19
, n,
Hold
n =
1.
Enable
2.
Disable (default)
The Bearer Capabilities 384k Unrestricted (H0), 1536k Unrestricted
(H11), 1920k Unrestricted, Restricted Digital Info, Trunk Video and
Unrestricted Multirate are not used and should remain disabled.
302-20
B Ch Selection
Method
FB20
, n,
Hold
n =
1.
Exclusive
2.
Preferred
3.
Any
The method used for selecting an idle ëBí channel and the reaction if
the PSTN indicates the channel is not available needs to be chosen to
originate a call from CTX.
Preferred option is recommended, unless PSTN needs other choice.
302-21
B Ch Selection
FB21
, n,
Hold
n1 =
1.
Forward Cyclic
2.
Backward Cyclic
3.
Forward Terminal
4.
Backward Terminal
The search method for choosing an idle ëBí channel shall also be
specified. Backward Terminal is the normal method with the PSTN
following a Forward Terminal method.
302-22
T1 Time Slot Pattern
FB22
, n,
Hold
n =
1.
Fixed1 (default)
2.
Fixed2
3.
Flexible
1544 Time Slot Pattern.
302-23
E1 Time Slot Pattern
FB23
, n,
Hold
n =
1.
Fixed1 (default)
2.
Fixed2
3.
Flexible
2048 Time Slot Pattern.
302-24
T-Wait Timer
FB24
, n,
Hold
n =
1.
Enable
2.
Disable (default)
Specify whether the T-Wait timer is to be enabled or disabled. This
field is only valid for Natíl ISDN.
302-25
RBT on Incoming Call
FB25
, n,
Hold
n =
1.
Enable (default)
2.
Disable
Enable Ringback Tone when terminating a call. This field is only valid
for Natíl ISDN.
302-26
Network Mode
FB26
, n,
Hold
n =
1.
Master
2.
Slave (default)
Set this span as Master or Slave for Layer 2 of a QSIG PRI. The
opposite value must be set for the node in which this QSIG PRI
terminates. This governs call setup activity and is not related to clock
synchronization.
302-27
Negotiation Priority
FB27
, n,
Hold
n =
1.
Side A (default)
2.
Side B
Sets this span as Side A or Side B for Layer 3 of a QSIG PRI. The
opposite value must be set for the node in which this QSIG PRI
terminates.
Table 1-26
Programs 300~302
(continued)
Button
Sequence
Value(s)
Summary