55 creating a patch, Output – Roland Fantom-S88 User Manual

Page 55

Creating a Patch

Output

Patch Out Assign

Specifies for each patch how the direct sound will be output.

Value:

MFX:

Output in stereo through multi-effects. You can also apply
chorus or reverb to the sound that passes through multi-
effects.

A, B:

Output to the OUTPUT A (MIX) jack or OUTPUT B jack in
stereo without passing through multi-effects.

1–4:

Output to the INDIVIDUAL 1–4 jacks in mono without
passing through multi-effects.

TONE: Outputs according to the settings for each tone.

* When the settings are such that signals are split and output from the

INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, and no plug is
inserted in the INDIVIDUAL 2 jack, the sounds from INDIVIDUAL 1
and INDIVIDUAL 2 are mixed together, then output from the
INDIVIDUAL 1 jack. This sound comprises the sounds from the
INDIVIDUAL 1 and 2 jacks.

* If the Mix/Parallel parameter ([MENU]/System/General) is set to

“MIX,” all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 193).

Tone Out Assign

Sets the direct sound’s output method for each tone.

Value:

MFX: Output in stereo through multi-effects. You can also apply

chorus or reverb to the sound that passes through multi-
effects.

A, B: Output to the OUTPUT A (MIX) jack or OUTPUT B jack in

stereo without passing through multi-effects.

1–4: Output to the INDIVIDUAL 1–4 jacks in mono without

passing through multi-effects.

• If the Patch Output Assign is set to anything other than “TONE,”

these settings will be ignored.

• When the Structure Type parameter has a setting of Type “2”–

”10,” the outputs of tones 1 and 2 will be combined with tone 2,
and the outputs of tones 3 and 4 will be combined with tone 4.
For this reason, tone 1 will follow the settings of tone 2, and tone
3 will follow the settings of tone 4 (p. 46).

• When the settings are such that signals are split and output from

the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, and no plug is
inserted in the INDIVIDUAL 2 jack, the sounds from
INDIVIDUAL 1 and INDIVIDUAL 2 are mixed together, then
output from the INDIVIDUAL 1 jack. This sound comprises the
sounds from the INDIVIDUAL 1 and 2 jacks.

If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 193).

• When setting the “MFX,” set the output destination with the

MFX Output Assign (p. 179) for the sound after it has passed
through the multi-effects.

• Chorus and reverb are output in mono at all times.

• The output destination of the signal after passing through the

chorus is set with the Chorus Output Select (p. 177) and the
Chorus Output Assign (p. 177).

• The output destination of the signal after passing through the

reverb is set with the Reverb Output Assign (p. 177).

Tone Out Level

Set the level of the signal that is sent to the output destination
specified by Tone Output Assign.

Value: 0–127

Tone Chorus Send
(Send Level (Output=MFX))

Specifies the level of the signal sent to the chorus for each tone if the
tone is sent through MFX.

Value: 0–127

Tone Reverb Send
(Send Level (Output=MFX))

Specifies the level of the signal sent to the reverb for each tone if the
tone is sent through MFX.

Value: 0–127

Tone Chorus Send
(Send Level (Output=non MFX))

Sets the level of the signal sent to chorus for each tone if the tone is
not sent through MFX.

Value: 0–127

Tone Reverb Send
(Send Level (Output=non MFX))

Sets the level of the signal sent to reverb for each tone if the tone is
not sent through MFX.

Value: 0–127