Roland Fantom-S88 - Manual (Page 155)

155
Editing Songs
Editing Songs
Range Min, Range Max
If you have set the Status parameter to “NOTE,” “P.AFT,” “C.C,” or
“PROG,” specify the range. Set “Range Min” to the lowest value of
the range, and “Range Max” to the highest value of the range.
• To erase all notes or polyphonic aftertouch data, set “Range
Min” to “C -1” and “Range Max” to “G9.” To erase C4, set
“Range Min” and “Range Max” to “C4.” To erase C3 through
C4, set “Range Min” to “C 3” and “Range Max” to “C4.”
• To erase all controller numbers, set “Range Min” to “0” and
“Range Max” to “127.” To erase all program numbers, set
“Range Min” to “1” and “Range Max” to “128.” To erase number
4, set “Range Min” and “Range Max” to “4.” To erase numbers 3
through 14, set “Range Min” to “3” and “Range Max” to “14.”
MIDI Channel
Selects the MIDI channel of the data to be erased.
When you want to erase all sequencer data, set this parameter to
“ALL.” To erase sequencer data of one specific MIDI channel only,
select that MIDI channel.
Value: ALL, 1–16
If you set the Track parameter to “TEMPO,” or if the Status
parameter is set to “EXC,” “TUNE” or “PTN,” the Channel
parameter will not be available.
Deleting Unwanted Measures (Delete)
This function deletes a specified area of sequencer data, and moves
the subsequent data to fill the gap. As a result, the measure length
will be shortened by the number of deleted measures.
fig.11-16_50
For details on the settings, refer to “Basic Operation for Track
Editing” (p. 151)
Track / Pattern
Specifies the track(s) or pattern that is to be deleted.
Value
ALL: Phrase tracks 1–16, the beat track, and the tempo track
TRK 1–TRK 16: The specified phrase track
TEMPO: Tempo track
PTN001–PTN100: The specified pattern
Measure, For (Edit Range)
Specifies the range of measures that are to be deleted. If you set
“For” to “ALL,” all measures will be specified.
Copying Phrases (Copy)
This function copies a specified area of sequencer data. It is convenient
for repeating the same phrase several times. You can copy patterns to a
phrase track, or copy data from a phrase track to a pattern.
fig.11-17_50
For details on the settings, refer to “Basic Operation for Track
Editing” (p. 151)
Src Track / Pattern (Source Track / Pattern)
Specifies the copy-source track(s) or pattern.
Value
ALL: Phrase tracks 1–16, the beat track, and the tempo track
TRK 1–TRK 16: The specified phrase track
TEMPO: Tempo track
PTN001–PTN100: The specified pattern
Src Measure, For (Edit Range)
Specifies the range of copy-source measures. If you set “For” to
“ALL,” all measures will be specified.
Dst Track/ Pattern (Destination Track/Pattern)
Check/modify the copy-destination track or pattern.
Value
ALL: Phrase tracks 1–16, the beat track, and the tempo track
TRK 1–TRK 16: The specified phrase track
TEMPO: Tempo track
PTN001–PTN100: The specified pattern
• If you set the source track to “ALL,” the destination track can be
set to either “ALL” or “PTN001–PTN100.” If you select
“PTN001–PTN100,” the data from the 16 phrase tracks will be
merged as it is copied.
• If “TEMPO” is selected as the source track, then only “Tempo”
can be selected for the destination track.
Dst Measure (Destination Measure)
Specifies the copy-destination measure.
If you want the copy destination to be right after the last measure of
a song, set this parameter to “END.”
Copy Mode
Specifies whether you want to preserve the existing data in the copy
destination when copying.
Value
MIX: Combines the data from the copy source with the
existing data in the copy destination.