Konica Minolta Polygon Editing Tool - Manual (Page 137)

135
Chapter
2
File
Menu
910
File – Import – Digitizer – Easy Align
Parameters in the [File-Import-Digitizer-Easy Align] Dialog
Parameters Tab
Auto Maker Detection Check this checkbox if using markers.
Settings When you click this button, the button’s name changes to [Calibration]. You can then change
the color level and carry out calibration. This button appears only if the [Auto Maker Detection]
checkbox is checked
Color Level Checking this checkbox sets the program to use color exposure level.
Calibration If this checkbox is checked, the program gets a color image and generates a reference file from
it. This check box appears only if the [Auto Maker Detection] checkbox is checked.
Log If this checkbox is checked, the program applies logarithmic correction to color data. Use if you
want to brighten up neutral colors. This check box appears only if the [Auto Maker Detection]
checkbox is unchecked.
Smooth If this checkbox is checked, the program applies smoothing to color data. Use if illumination is
low and the image is unclear. This check box appears only if the [Auto Maker Detection] check-
box is unchecked.
Dark If this checkbox is checked, the program applies dark correction to color data. Use if you are get-
ting striation-type noise in the images. This check box appears only if the [Auto Maker Detec-
tion] checkbox is unchecked.
Turntable Tab
Apply When you click the [Apply] button after selecting the serial port and rotating stage, the [Angle]
slidebar becomes effective and stage control is enabled.
Note
If connecting to a SKIDS-60YAW unit, select “CSG-602R (Ver.1.0)” from the menu. If connecting to a
SKIDS-60YAW (Ver.2.0) unit, select “CSG-602R (Ver.2.0)”.
Angle The Angle slidebar becomes enabled when the program determines that the rotating stage is
operating normally. You can use the slidebar to control the stage’s rotation.
Parameters in the [File-Import-Digitizer-Easy Align-Convert] Dialog
Reduction Rate Selects the reduction rate to be applied when importing data. You can select any of the following:
“1/1”, “1/4”, “1/9”, “1/16”, or “No polygon”.
Fill Holes Selects whether the program fills in holes when importing the data. If the setting is On, the pro-
gram will automatically generate points to fill in holes left by missing data.
Remove Selects which data the program excludes when carrying out the import. Select from any of the fol-
lowing: “None”, “Boundary (B.)”, “5deg. & B.”, “10deg &B.”, “15deg & B.”, or “20deg. & B.”
None: No removal when importing the data.
Boundary (B.): The program removes boundary points.
5deg & B., 10deg & B., 15deg. & B., 20deg. & B.:
The program removes boundary points and also removes polygons within
the specified angular range (5°,10°, 15°, or 20°) to the view vector.
Filter None: The program does not perform filtering when importing the data.
Noise Filter (N.F.): When importing data, the program corrects the points that appear to be noise.
High Quality (H.Q.): The program filters out unreliable data. (Effective only when importing
data that was scanned using the VIVID 910.)
H.Q & N.F.: Applies both noise filter and high quality filter. (Effective only when im-
porting data that was scanned using the VIVID 910.)
Marker Correction None: The program does not perform filtering the marker sections.
Cut marker: The data in the marker section will be deleted and treated as a hole.
Smooth marker: Smoothing will be carried out for the marker section data.
Use Texture Check this checkbox when using texture.
Save Data If you check this checkbox, the program will automatically save the data into a camera data file
when carrying out conversion.
Note
If you select CDM as the file type for the save (at the Save dialog that appears) , the program will not include the
above-described data corrections and data-coordinate conversion information into the saved file. If you select a
file type other than CDM, however, the program does incorporate this information into the save.