Maxim Integrated MAXQ Family Users Guide: MAXQ8913 Supplement Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for MAXQ Family Users Guide: MAXQ8913 Supplement Maxim Integrated
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 114 |
| Size: | 1.73 MB |
Show table of contents
Document Outline
- ADDENDUM TO SECTION 1: OVERVIEW
- ADDENDUM TO SECTION 2: ARCHITECTURE
- ADDENDUM TO SECTION 3: PROGRAMMING
- ADDENDUM TO SECTION 4: SYSTEM REGISTER DESCRIPTIONS
- ADDENDUM TO SECTION 5: PERIPHERAL REGISTER MODULES
- ADDENDUM TO SECTION 6: GENERAL-PURPOSE I/O MODULE
- 6.1 GPIO and External Interrupt Register Descriptions
- 6.1.1 Port 0 Direction Register (PD0, M0[10h])
- 6.1.2 Port 1 Direction Register (PD1, M0[11h])
- 6.1.3 Port 0 Input Disable Register (PID0, M0[0Dh])
- 6.1.4 Port 0 Output Register (PO0, M0[00h])
- 6.1.5 Port 1 Output Register (PO1, M0[01h])
- 6.1.6 Port 0 Input Register (PI0, M0[08h])
- 6.1.7 Port 1 Input Register (PI1, M0[09h])
- 6.1.8 External Interrupt Flag 0 Register (EIF0, M0[02h])
- 6.1.9 External Interrupt Flag 1 Register (EIF1, M0[04h])
- 6.1.10 External Interrupt Enable 0 Register (EIE0, M0[03h])
- 6.1.11 External Interrupt Enable 1 Register (EIE1, M0[05h])
- 6.1.12 External Interrupt Edge Select 0 Register (EIES0, M0[0Ah])
- 6.1.13 External Interrupt Edge Select 1 Register (EIES1, M0[0Bh])
- 6.2 Port Pin Examples
- 6.1 GPIO and External Interrupt Register Descriptions
- ADDENDUM TO SECTION 7: TIMER/COUNTER 0 MODULE
- ADDENDUM TO SECTION 8: TIMER/COUNTER 1 MODULE
- ADDENDUM TO SECTION 9: TIMER/COUNTER 2 MODULE
- ADDENDUM TO SECTION 10: SERIAL I/O MODULE
- ADDENDUM TO SECTION 11: SERIAL PERIPHERAL INTERFACE (SPI) MODULE
- ADDENDUM TO SECTION 12: HARDWARE MULTIPLIER MODULE
- ADDENDUM TO SECTION 13: 1-Wire BUS MASTER
- ADDENDUM TO SECTION 14: REAL-TIME CLOCK MODULE
- ADDENDUM TO SECTION 15: TEST ACCESS PORT (TAP)
- ADDENDUM TO SECTION 16: IN-CIRCUIT DEBUG MODE
- ADDENDUM TO SECTION 17: IN-SYSTEM PROGRAMMING (JTAG)
- 17.1 JTAG Bootloader Protocol
- 17.2 Family 0 Commands (Not Password Protected)
- 17.3 Family 1 Commands: Load Variable Length (Password Protected)
- 17.4 Family 2 Commands: Dump Variable Length (Password Protected)
- 17.5 Family 3 Commands: CRC Variable Length (Password Protected)
- 17.6 Family 4 Commands: Verify Variable Length (Password Protected)
- 17.7 Family 5 Commands: Load and Verify Variable Length (Password Protected)
- 17.8 Family E Commands: Erase Fixed Length (Password Protected)
- ADDENDUM TO SECTION 18: MAXQ FAMILY INSTRUCTION SET SUMMARY
- SECTION 19: ANALOG-TO-DIGITAL CONVERTER (SPECIFIC TO MAXQ8913)
- 19.1 Analog-to-Digital Converter Features
- 19.2 Analog-to-Digital Pins and Control Registers
- 19.2.1 Analog-to-Digital Converter Status Register (ADST, M4[06h])
- 19.2.2 ADC Conversion Sequence Address Register (ADADDR, M3[01h])
- 19.2.3 ADC Control Register (ADCN, M3[08h])
- 19.2.4 ADC Data Register (ADDATA, M3[09h])
- 19.2.5 ADC Data Buffer Registers (ADBUF[0] to ADBUF[15], ADDATA[00h] to ADDATA[0Fh])
- 19.2.6 ADC Conversion Configuration Registers (ADCFG[0] to ADCFG[7], ADDATA[10h] to ADDATA[17h])
- 19.2.7 Temperature Sensor Enable Register (TEMPEN, M3[0Ch])
- 19.3 Analog-to-Digital Converter Code Examples
- SECTION 20: DIGITAL-TO-ANALOG CONVERTERS (SPECIFIC TO MAXQ8913)
- SECTION 21: TIMER/COUNTER B MODULE (SPECIFIC TO MAXQ8913)
- 21.1 Timer/Counter B Register Descriptions
- 21.2 Timer/Counter B Operation
- 21.2.1 Timer B 16-Bit Timer/Counter Mode with Autoreload
- 21.2.2 Timer B 16-Bit Capture Mode
- 21.2.3 Timer B 16-Bit Up/Down Count with Autoreload Mode
- 21.2.4 Timer B Clock Output Mode
- 21.2.5 Timer B PWM/Output Control Functionality
- 21.2.6 16-Bit Up Count PWM/Output Control Mode
- 21.2.7 16-Bit Up/Down Count PWM/Output Control Mode
- 21.2.8 EXENB Control During PWM/Output Control Mode
- 21.3 Timer B Examples
- SECTION 22 : I2C BUS INTERFACE (SPECIFIC TO MAXQ8913)
- 22.1 I2C Register Descriptions
- 22.1.1 I2C Data Buffer Register (I2CBUF, M1[06h])
- 22.1.2 I2C Status Register (I2CST, M3[01h])
- 22.1.3 I2C Interrupt Enable Register (I2CIE, M1[07h])
- 22.1.4 I2C Control Register (I2CCN, M1[04h])
- 22.1.5 I2C Clock Control Register (I2CCK, M1[0Ch])
- 22.1.6 I2C Timeout Register (I2CTO, M1[0Dh])
- 22.1.7 I2C Slave Address Register (I2CSLA, M1[0Eh])
- 22.2 I2C Code Examples
- 22.1 I2C Register Descriptions
- SECTION 23: SUPPLY VOLTAGE MONITOR AND POWER CONTROL(SPECIFIC TO MAXQ8913)
- SECTION 24: INPUT/OUTPUT AMPLIFIERS (SPECIFIC TO MAXQ8913)
- SECTION 25: UTILITY ROM (SPECIFIC TO MAXQ8913)
- APPENDIX 1: MAXQ8913 DEVICE INCLUDE FILE FOR MAX-IDE
- REVISION HISTORY