Magnum Energy AGS Network (ME-AGS-N) - Manual (Page 32)

7.0 Using a Remote with the ME-AGS-N
© 2012 Magnum Energy, Inc. 26
AGS Feature
Inverter
Level
Remote Control /
Revision Required
Required ME-RC ME-ARC ME-RTR
Turn gen on/off with remote ≥ Level 1 NA ≥ 2.0 ≥ 2.0
Displays DC voltage to AGS ≥ Level 1 ≥ 1.5 ≥ 2.0 ≥ 2.0
Displays gen run time ≥ Level 1 ≥ 1.5 ≥ 2.0 ≥ 2.0
Displays AGS temperature ≥ Level 1 ≥ 1.5 ≥ 2.0 ≥ 2.0
Displays days since gen last ran ≥ Level 1 ≥ 1.5 ≥ 2.0 ≥ 2.0
Gen starts on temp/stops on time ≥ Level 1 ≥ 1.5 ≥ 2.0 ≥ 2.0
Gen starts on VDC/stops on time ≥ Level 1 ≥ 1.5 NA NA
Gen starts on VDC/stops on VDC
or Float charge
≥ Level 1 NA ≥ 2.0 ≥ 2.0
Gen starts/stops based on time
of day
≥ Level 1 NA ≥ 2.0 ≥ 2.0
Gen starts/stops based on inverter
AC amps
≥ Level 4
[Note 1]
NA ≥ 2.0 ≥ 2.0
Gen starts/stops based on battery
SOC [Note 2]
≥ Level 1 NA ≥ 2.0 ≥ 2.0
Set Max Gen Run Time ≥ Level 1 NA ≥ 2.0 ≥ 2.0
Set Gen Quiet Time ≥ Level 1 ≥ 1.5 ≥ 2.0 ≥ 2.0
Set Gen Exercise ≥ Level 1 NA ≥ 2.0 ≥ 2.0
Set Gen Warm-up Time ≥ Level 1 NA ≥ 2.0 ≥ 2.0
Set Gen Cooldown Time ≥ Level 1 NA ≥ 2.0 ≥ 2.0
[1] Only applicable to MS-PAE and MS-PE inverters.
[2] The gen start/stop SOC feature requires the ME-BMK (Battery Monitor) to be
installed.
7.0 Using a Remote with the ME-AGS-N
When an AGS is released with a new software revision, some of the fea-
tures and functionality in the new AGS may not be available in an inverter
or remote control that has an earlier software version. Before continuing to
your specifi c remote control section in this manual, you should evaluate the
software compatibility between your inverter, remote control, and AGS to
determine what AGS features are available.
7.1 AGS to Inverter Compatibility
Magnum Energy’s AGS has many advanced features, and these features
work with your Magnum inverter using the settings/setup menus provided in
a Magnum remote control (i.e., ME-RC, ME-ARC, and ME-RTR). Depending
on the desired AGS feature, you must ensure that the feature is compatible
with your inverter and is available in your remote control.
To determine your inverter’s compatibility level, go to:
http://www.magnumenergy.com/service/compatibility.htm
After identifying the inverter’s compatibility level, use Table 7-1 below to fi nd
the AGS feature and determine if the inverter is at a level that is compat-
ible; and, which remote control and revision is required to provide the AGS
feature you desire.
Table 7-1, AGS Compatibility Matrix Chart