Yaskawa G7 Drive User Manual
Page 446
User Parameters
10-
23
H3-05
Multi-function analog input (termi-
nal A3)
2
L2-04
Voltage recovery time
0.3
H3-06 Gain (terminal A3)
100.0
L2-05
Undervoltage detection level
190
*7
H3-07 Bias (terminal A3)
0.0
L2-06
KEB deceleration time
0.0
H3-08
Multi-function analog input termi-
nal A2 function selection
2
L2-07
Momentary recovery time
0
*11
H3-09
Multi-function analog input termi-
nal A2 signal level selection
0
L2-08
Frequency reduction gain at KEB
start
100
H3-10 Gain (terminal A2)
100.0
L3-01
Stall prevention selection during
accel
1
H3-11 Bias (terminal A2)
0.0
L3-02
Stall prevention level during accel
150
H3-12 Analog input filter time constant
0.03
L3-03
Stall prevention limit during accel
50
H4-01 Monitor selection (terminal FM)
2
L3-04
Stall prevention selection during
decel
1
H4-02 Gain (terminal FM)
1.00
L3-05
Stall prevention selection during
running
1
H4-03 Bias (terminal FM)
0.0
L3-06
Stall prevention level during run-
ning
160
H4-04 Monitor selection (terminal AM)
3
L4-01
Speed agreement detection level
0.0
H4-05 Gain (terminal AM)
0.50
L4-02
Speed agreement detection width
2.0
H4-06 Bias (terminal AM)
0.0
L4-03
Speed agreement detection level
(+/-)
0.0
H4-07
Analog output 1 signal level selec-
tion
0
L4-04
Speed agreement detection width
(+/-)
2.0
H4-08
Analog output 2 signal level selec-
tion
0
L4-05
Operation when frequency refer-
ence is missing
0
H5-01 Station address
1F
L5-01
Number of auto restart attempts
0
H5-02 Communication speed selection
3
L5-02
Auto restart operation selection
0
H5-03 Communication parity selection
0
L6-01
Torque detection selection 1
0
H5-04
Stopping method after communi-
cation error
3
L6-02
Torque detection level 1
150
H5-05
Communication error detection
selection
1
L6-03
Torque detection time 1
0.1
H5-06 Send wait time
5
L6-04
Torque detection selection 2
0
H5-07 RTS control ON/OFF
1
L6-05
Torque detection level 2
150
H6-01 Pulse train input function selection
0
L6-06
Torque detection time 2
0.1
H6-02 Pulse train input scaling
1440
L7-01
Forward drive torque limit
200
H6-03 Pulse train input gain
100.0
L7-02
Reverse drive torque limit
200
H6-04 Pulse train input bias
0.0
L7-03
Forward regenerative torque limit
200
H6-05 Pulse train input filter time
0.10
L7-04
Reverse regenerative torque limit
200
H6-06 Pulse train monitor selection
2
L8-01
Protect selection for internal DB
resistor (Type ERF)
0
H6-07 Pulse train monitor scaling
1440
L8-02
Overheat pre-alarm level
95
L1-01
Motor protection selection
1
L8-03
Operation selection after overheat
pre-alarm
3
L1-02
Motor protection time constant
1.0
L8-05
Input open-phase protection selec-
tion
0
L1-03
Alarm operation selection during
motor overheating
3
L8-07
Output open-phase protection
selection
0
L1-04
Motor overheating operation selec-
tion
1
L8-09
Ground protection selection
1
L1-05
Motor temperature input filter time
constant
0.20
L8-10
Cooling fan control selection
0
L2-01
Momentary power loss detection
0
L8-11
Cooling fan control delay time
60
L2-02
Momentary power loss ridethru
time
0.1
*6
L8-12
Ambient temperature
45
L2-03
Min. baseblock time
0.5
L8-15
OL2 characteristics selection at
low speeds
1
Table 10.7 User Parameters (Continued)
No.
Name
Factory
Setting
Setting
No.
Name
Factory
Setting
Setting