Yaskawa G7 Drive User Manual
Page 445
10
-22
E3-05
Motor 2 mid. output frequency 1
(FB)
3.0
*2
F4-08
Analog output signal level for
channel 2
0
E3-06
Motor 2 mid. output frequency
voltage 1 (VC)
12.6
*7
F5-01
Channel 1 output selection
0
E3-07
Motor 2 min. output frequency
(FMIN)
0.5
*2
F5-02
Channel 2 output selection
1
E3-08
Motor 2 min. output frequency
voltage (VMIN)
2.3
*7
F5-03
Channel 3 output selection
2
E4-01 Motor 2 rated current
1.90
*6
F5-04
Channel 4 output selection
4
E4-02 Motor 2 rated slip
2.90
*6
F5-05
Channel 5 output selection
6
E4-03 Motor 2 no-load current
1.20
*6
F5-06
Channel 6 output selection
37
E4-04
Motor 2 number of poles (number
of poles)
4
F5-07
Channel 7 output selection
0F
E4-05 Motor 2 line-to-line resistance
9.842
*6
F5-08
Channel 8 output selection
0F
E4-06 Motor 2 leak inductance
18.2
*6
F5-09
DO-08 output mode selection
0
E4-07 Motor 2 rated capacity
0.40
*6
F6-01
Operation selection after commu-
nications error
1
F1-01
PG constant
1024
F6-02
Input level of external fault from
Communications Option Card
0
F1-02
Operation selection at PG open cir-
cuit (PGO)
1
F6-03
Stopping method for external fault
from Communications Option
Card
1
F1-03
Operation selection at overspeed
(OS)
1
F6-04
Trace sampling from Communica-
tions Option Card
0
F1-04
Operation selection at deviation
3
F6-06
Torque reference/torque limit
selection from optical option
1
F1-05
PG rotation
0
H1-01 Terminal S3 function selection
24
F1-06
PG division rate (PG pulse moni-
tor)
1
H1-02 Terminal S4 function selection
14
F1-07
Integral value during accel/decel
enable/disable
0
H1-03 Terminal S5 function selection
3 (0)
*8
F1-08
Overspeed detection level
115
H1-04 Terminal S6 function selection
4 (3)
*8
F1-09
Overspeed detection delay time
0.0
H1-05 Terminal S7 function selection
6 (4)
*8
F1-10
Excessive speed deviation detec-
tion level
10
H1-06 Terminal S8 function selection
8 (6)
F1-11
Excessive speed deviation detec-
tion delay time
0.5
H1-07 Terminal S9 function selection
5
F1-12
Number of PG gear teeth 1
0
H1-08 Terminal S10 function selection
32
F1-13
Number of PG gear teeth 2
0
H1-09 Terminal S11 function selection
7
F1-14
PG open-circuit detection time
2.0
H1-10 Terminal S12 function selection
15
F2-01
Bi-polar or uni-polar input selec-
tion
0
H2-01
Terminal M1-M2 function selec-
tion (contact)
0
F3-01
Digital input option
0
H2-02
Terminal M3-M4 function selec-
tion (open collector)
1
F4-01
Channel 1 monitor selection
2
H2-03
Terminal M5-M6 function selec-
tion (open collector)
2
F4-02
Channel 1 gain
1.00
H2-04
Terminal P3 function selection
(open-collector)
6
F4-03
Channel 2 monitor selection
3
H2-05
Terminal P4 function selection
(open-collector)
5
F4-04
Channel 2 gain
0.50
H3-01
Signal level selection (terminal
A1)
0
F4-05
Channel 1 output monitor bias
0.0
H3-02 Gain (terminal A1)
0
F4-06
Channel 2 output monitor bias
0.0
H3-03 Bias (terminal A1)
100.0
F4-07
Analog output signal level for
channel 1
0
H3-04
Signal level selection (terminal
A3)
0
Table 10.7 User Parameters (Continued)
No.
Name
Factory
Setting
Setting
No.
Name
Factory
Setting
Setting