Moniteur 50 Series SMART Positioners - Manual (Page 75)

inverted
inverted
normal
normal
If "turn" is selected, you cannot set 33°
Parameter does not appear if 1.YFCT=turn has been selected
if TSI= AUto not active
Turning points only appear wih selection 8.SFCT = FrEE
NC contact means:
NO contact means:
normal means:
inverted means: 1)
2)
3)
4) 5)
6)
3.YWAY
Stroke range
If used, must match set leverage ratio on
the actuator
Driver pin must be set to the value of the actuator
travel or, if this value is not scaled, to the next
larger scale value.
(Setting optional)
mm
2)
1)
4.INIT
6.TSI
7.TSD
8.SFCT
09.SL0
10.SL1
etc. to
28.SL19
29.SL20
Initialization
Setpoint ramp OPEN
Setpoint ramp CLOSE
Setpoint function
Setpoint direction
Setpoint turning point at 0%
5%
etc. to
95%
100%
0.0
5.0
etc. to
95.0
100.0
5.SDIR
no / ###.#
Strt
riSE
FALL
AUto
0 to 400
0 to 400
Lin
1 : 33
FrEE
n1 : 33
1 : 50
n1 : 50
1 : 25
n1 : 25
0.0 to 100.0
Lin
0
0
%
s
s
riSE
4)
3)
oFF
40 | 50 | 60 | 70 | 90 | 110 | 130
25 | 30 | 35
5 | 10 | 15 | 20
oFF
(short lever 33°)
(short lever 90°)
(long lever 90°)
2.YAGL
90°
33°
Degrees 33°
Rated angle of rotation of feedback
Type of actuator 1.YFCT WAY
turn (part-turn actuator)
WAY (linear actuator)
LWAY (linear actuator
without sine correction)
(example)
Set transmission ratio selector (7) appropriately
(see view of device)
no
Linear
Equal-percentage 1: 25, 1:33, 1:50
inverse Equal-percentage 25:1, 33:1, 50:1
Freely adjustable
30.DEBA
31.YA
32.YE
34.YCLS
35.YCDO
36.YCUP
Dead zone of controller
Start of manipulated variable limiting
End of manipulated variable limiting
Standardization of
manipulated variable
Tight closing with manipulated variable
Value for tight closing below
Value for tight closing above
AUto
0.1 to 10.0
0.0 to 100.0
0.0 to 100.0
0.0 to 100.0
0.0 to 100.0
MPoS
FLow
no
uP:
:dW
uP:dW
no
MPoS
100.0
100.0
0.0
0.0
AUto
%
%
%
33.YNRM
Without
Top only
Bottom only
Top and bottom
To mech. travel
To flow
6)
6)
rising
falling
%
%
30
126
0.0
90.0
10.0
oFF
oFF
oFF 5)
5)
No
cont
act
No
cont
act
NC
cont
act
NC
cont
act
on
uP
doW
StoP
-on
-uP
-doW
-StP
on
bLc1
bLc2
uP
doW
StoP
-on
-uP
-doW
-StP
no
Strt
oCAY
FSVL
FSSP
FSAC
FSVL
no
AUto s
s
%
%
AUto Response threshold of alarm
Parameter name Display Function Parameter values Unit Factory setting
Customer
setting
Function of BI 1
Function of BI 2
Function of alarm output
action with opened switch or Low level
action with closed switch or High level
High level without fault
Low level without fault