FaxBack NET SatisFAXtion 9.0 - Fax Server Manual - Manual (Page 179)

the application sooner when connections fail. Default: 60000.
get_send_post_phase_ok_timeout_msecs [dword 0–65535]: This is how long to wait for
the OK after sending the +FET command. The modem will receive the post page response
during this period. When the driver receives this OK it will send the +FDT signal and wait for a
CONNECT or for a +FHNG.
get_send_pre_phase_ok_timeout_msecs [dword 0–65535]: This is how long to wait for
an OK while in the initial pre­phase of a fax send. When the driver receives an OK it will send a
+FDT. The modem usually receives CSI and DIS in this time period. Default: 35000.
hangup_timeout_msecs [dword 0–65535]: This is how long to wait for ATH0 command to
complete. Default: 2000.
line_type [string]: When dtmf_prompt is specified, the dtmf_detection_begin_string will be
sent at the start of the call and received DTMF digits will be collected from the modem up until
either a dtmf_terminate_digit is received or a 6 second inter­digit timeout occurs or a CNG tone
is detected or dtmf_digit_count number of digits are collected. Default: NORMAL.
hangup_timeout_msecs [dword 0–65535]: This is how long to wait for ATH0 command to
complete. Default: 2000.
line_type [string]: When dtmf_prompt is specified, the dtmf_detection_begin_string will be
sent at the start of the call and received DTMF digits will be collected from the modem up until
either a dtmf_terminate_digit is received or a 6 second inter­digit timeout occurs or a CNG tone
is detected or dtmf_digit_count number of digits are collected. Default: NORMAL.
next_ring_response_timeout_msecs [dword 0–65535]: This is how many msecs to wait
after a ring from the modem before resetting the internal ring counter. This will only apply for
rings_before_answer greater than 1 and when not using TAPI. Default: 7500.
on_hook_msecs [dword 0–65535]: This is the minimum amount of time after the modem
goes on hook from a prior connection before the driver will start a new connection (dial). This
will allow the phone system to have time to disconnect the call upon noticing the modem on
hook. Default: 200.
pause_before_send_command_msecs [dword 0–65535]: This specifies how long to pause
when the protocol state is idle, answering, or dialing, before sending the "AT" command. There
are some modems that upon sending an OK from a subsequent command, must have time to
get ready to receive new characters from the DTE. Default: 100.
periodic_reset_timeout_msecs [dword 0–4294967295]: How often a reset sequence should
be done to verify modem integrity. It is understood that some modems may periodically hang or
go into a disabled power saver type of mode or that they may be turned off and on but the DSR
modem control change is not detected possibly because TAPI is being used. Therefore, the driver
will reset the modem when it is idle for this amount of time. Setting this to 0 will disable this
periodic reset feature. Default: 600000.
receive_image_modulation_timeout_msecs [dword 0­65535]: How long to wait without
receiving any image data before canceling the reception of image data. There is a USR modem
that sometimes fails to send a DLE/ETX sequence at the end of image data. By having this
timeout short enough, the driver will abort the image receive in a timeliness manner so as to
receive one of the subsequent end of page commands. Default: 3000.
send_buffer_empty_flow_control [boolean]: If enabled and the send image buffer does not
contain a complete scan line or ECM frame, this causes a particular byte (0 or current ECM flag
Proprietary FaxBack, Inc. 2014 179