Unitec Wash Select II With WashPay Integration Operations Manual User Manual
Unitec
Table of contents
Document Outline
- 1 System Overview
- 2 Initial Setup
- 2.1 Credit System
- 2.2 Wash and Option Names and Prices
- 2.3 Speech Menu
- 2.4 Text Messages Menu
- 2.5 Wash Interface Menu
- 2.5.1 Enable Relay Stacking
- 2.5.2 Enable Relay Latching
- 2.5.3 Configure the Wash Relay Pattern
- 2.5.4 Enable Automatic Out-Of-Service Detection
- 2.5.5 Wash Handshaking
- 2.5.6 Wash Fault
- 2.5.7 OOS Timer
- 2.5.8 Tunnel Wash Settings
- 2.5.9 Combo Mode
- 2.5.10 Edit Combo Names
- 2.5.11 Optioning
- 2.5.12 Remote Code POS4000 Support
- 2.6 Customer Interface Menu
- 2.7 Paging Functions
- 2.8 Cash and Tokens Menu
- 2.9 Miscellaneous Setup Menu
- 2.10 Remote Reporting Menu
- 2.11 Pass Codes and Pass Cards
- 2.12 VIP Wash Coupons
- 2.13 POS4000 Link
- 3 Daily Operations
- 3.1 Reporting Menu
- 3.2 Fleet Accounts and Coupons Menu
- 3.3 Cash Reconciliation
- 3.4 Diagnostics Menu
- 3.4.1 Testing Output Relays
- 3.4.2 Cycling Output Relays
- 3.4.3 Testing Inputs
- 3.4.4 Testing Coin and Bill Pulse Relays
- 3.4.5 Test Coin Dispenser
- 3.4.6 Testing the Magnetic Card Reader
- 3.4.7 Testing the Thermal Printer
- 3.4.8 Testing the Standard Keypad
- 3.4.9 Testing the Buttons
- 3.4.10 Test Exp. Memory
- 3.4.11 Test RFID (AWID)
- 3.4.12 Inapplicable Diagnostics with WashPay Integration
- 1.1.1
- 4 Component Operation & Maintenance
- 4.1 Component Locations
- 4.2 Software Updates
- 4.3 Bill Validator
- 4.3.1 Mars Bill Validator
- 4.3.1.1 Emptying the Bill Stacker
- 4.3.1.2 Replacing the Stacker
- 4.3.1.3 Mars Bill Validator Flash Codes
- 4.3.1.4 Removing the Mars Bill Validator From the WASH SELECT II
- 4.3.1.5 Removing the Mars Bill Validator Lower Housing
- 4.3.1.6 Cleaning and General Maintenance
- 4.3.1.7 Programming the Mars Bill Validator
- 4.3.1 Mars Bill Validator
- 4.4 Single Coin Acceptor
- 4.5 Multi-Coin Acceptor Programming and Operation
- 4.5.1 Programming the IDX Acceptor
- 4.5.2 Programming the IDX to Accept Site-Specific Tokens
- 4.5.3 Programming Token Value
- 4.5.4 Programming Dispense Value (for $1 coin dispensing only)
- 4.5.5 Modifying the Hopper
- 4.5.6 Program the IDX to Accept Quarters
- 4.5.7 Programming the IDX to Accept $1 Coins
- 4.5.8 Erasing IDX Programming
- 4.5.9 The Token Bucket
- 4.5.10 Cleaning and General Maintenance
- 4.5.11 System Settings Affecting IDX Coin Acceptor Operations
- 4.6 Speech Module
- 4.7 Proximity Sensor
- 4.8 Coin Hopper and Assembly
- 4.9 Card Reader
- 4.10 Thermal Printer Assembly
- 4.11 Fuse