JUMO 902931 Wtrans Receiver with Wireless Data Transmission Operating Manual User Manual
Jumo wtrans receiver, With wireless data transmission
Table of contents
Document Outline
- b90.2931.0en_2010-06-01.pdf
- 1 Introduction
- 1.1 Safety information
- 1.2 Description
- 1.3 Block diagram
- 2 Identifying the instrument version
- 2.1 Rating plate
- 2.2 Type designation
- 2.3 Serial accessories
- 2.4 Accessories
- 3 Basics
- 3.1 Radio technology
- 3.2 General information about radio transmission
- 3.3 Reception characteristic of the lambda/4 antenna
- 3.4 Interferences
- 3.5 Function overview
- 3.6 Data flow diagram
- 4 Installation
- 4.1 Installation site and climatic conditions
- 4.1.1 Receiver
- 4.1.2 Antenna
- 4.2 Dimensions
- 4.2.1 Receiver
- 4.2.2 Lambda/4 antenna
- 4.2.3 Antenna wall holder for lambda/4 antenna
- 4.3 Receiver installation
- 4.4 Fitting the antenna
- 4.4.1 Antenna installation directly on the receiver
- 4.4.2 Antenna installation on the antenna wall holder
- 4.1 Installation site and climatic conditions
- 5 Electrical connection
- 5.1 Installation notes
- 5.2 Connection diagram
- 6 Display and key functions
- 6.1 Normal display (ND) (measured values and signal quality)
- 6.2 Commissioning/start-up level (In) (allocating the probe ID to a channel)
- 6.3 Parameter level (PA) (Parameter configuration)
- 6.4 Light diodes (independent of level)
- 7 Receiver operation
- 7.1 Normal display (ND)
- 7.2 Channels and their Display measured values
- 7.3 Display signal quality of the probes received
- 7.4 Changing to other Changing levels
- 7.5 Code interrogation
- 8 Configuration of the receiver
- 8.1 Commissioning/start-up level (In)
- 8.1.1 Selection of a transmitter ID from the link list and assignment to a channel
- 8.1.2 Manual assignment of a transmitter ID to a channel
- 8.1.3 Assignment of a transmitter ID to a channel via interface
- 8.1.4 Pre-configuration of all transmitter ID's using the setup program
- 8.1.5 Configuration of customized transmitter ID's on the transmitter side
- 8.2 Parameter level (PA)
- 8.2.1 Editing parameters
- 8.2.2 General parameters
- 8.2.3 Channel specific parameters
- 8.1 Commissioning/start-up level (In)
- 9 Term definition
- 9.1 General parameters
- 9.1.1 device information
- 9.1.2 Device data
- 9.1.3 RS485 interface
- 9.1.4 Analog outputs 1 to 4
- 9.1.5 Relay outputs 1 to 2
- 9.1.6 Modbus remote control values FLOAT 1 to 4
- 9.2 Channel specific parameters
- 9.1 General parameters
- 10 Display and reset fly back
- 11 Setup program
- 11.1 General information about the setup program
- 11.2 Hardware and software prerequisites
- 11.3 Connect PC and receiver to each other
- 11.4 Configuration of the receiver
- 11.4.1 Establishing the communication
- 11.4.2 Reading out the current receiver parameters
- 11.4.3 Editing receiver parameters
- 11.4.4 Transmit new parameters to the receiver
- 11.5 Customer-specific linearization
- 11.6 OnlineChart
- 12 Detect and remedy faults/errors
- 13 Supplement
- 13.1 Technical data
- 13.2 Table: Assignment of probes to the receiver channels
- 1 Introduction