KROHNE MFC 400 EN - Manual (Page 72)

6
OPERATION
72
MFC 400
www.krohne.com 08/2013 - 4002075802 - MA MFC 400 R02 en
C1.2.4 Ref. Density Slope Set the slope for the reference density option
Appears only if density mode "Referred" has been selected in Fct. C1.2.2.
C1.2.5 Standard Density Temp. Appears only if density mode "Standard" has been selected in Fct. C1.2.2.
Density reference temperature to calculate standard density
C1.2.6 Standard Density k0 Appears only if density mode "Standard" has been selected in Fct. C1.2.2.
Coefficient k
0
to calculate standard density
C1.2.7 Standard Density k1 Appears only if density mode "Standard" has been selected in Fct. C1.2.2.
Coefficient k
1
to calculate standard density
C1.2.8 Standard Density k2 Appears only if density mode "Standard" has been selected in Fct. C1.2.2.
Coefficient k
2
to calculate standard density
C1.2.9 Last Density Cal. Date of last density calibration
C1.3 Filter
C1.3 Filter -
C1.3.1 Flow Direction Define polarity of flow direction.
Forwards (according to the arrow on the measuring sensor) or backwards
(in the opposite direction to the arrow)
C1.3.2 Press. Supp. Time Set the pressure suppression time; range: 0.0...20.0 s
C1.3.3 Press. Supp. Cutoff Low flow cutoff settings for the pressure suppression; range: 0.0...10.0%
C1.3.4 Low Flow Cutoff Set the low flow cutoff; range: 00.0...10.0%
C1.4 System Control
C1.4 System Control -
C1.4.1 Function Set the system control.
Select: Inactive (off) / Flow = 0 (flow to zero)
C1.4.2 Sys. Ctrl. Condition Set the condition for activating the system control.
Selection: density or temperature
C1.4.3 Sys. Ctrl. Max Limit Defines the upper limit for the condition selected in C1.4.2
C1.4.4 Sys. Ctrl. Min Limit Defines the lower limit for the condition selected in C1.4.2
C1.5 Diagnosis
C1.5 Diagnosis -
C1.5.1 Max. Rec. Temp. Display of maximum recorded sensor temperature
C1.5.2 Min. Rec. Temp. Display of minimum recorded sensor temperature
C1.5.3 2 Ph. Threshold Defines the process-dependent sensitivity for 2 phase signal error message.
C1.5.4 Defines the parameter for the respective diagnostic value.
Select:
Off (goes to zero) / Sensor Average (sensor amplitude A+B) / Sensor
Deviation / Drive Level / MT Frequency / Strain 1 / Strain 2 /
2 Phase Signal
C1.5.5
C1.5.6
C1.5.7 Proc: Signal Low Selection of status signal (Failure, Out of Specification, Function Check,
Maintenance Required and Information) for the group "Proc: Signal Low"
C1.5.8 Proc: Signal Search Selection of status signal (Failure, Out of Specification, Function Check,
Maintenance Required and Information) for the group "Proc: Signal Search"
C1.5.9 Proc: Current Input Selection of status signal (Failure, Out of Specification, Function Check,
Maintenance Required and Information) for the group "Proc: Current Input"
C1.5.10 Proc: 2 Phase Flow Selection of status signal (Failure, Out of Specification, Function Check,
Maintenance Required and Information) for the group "Proc: 2 Phase Flow"
No. Function Settings / descriptions
.book Page 72 Monday, August 26, 2013 9:05 AM