Yokogawa 2-Wire Dual Channel Transmitter/Analyzer FLXA21 - Manual (Page 170)

<15. OPERATION OF SENCOM pH/ORP>
15-1
IM 12A01A02-01E 5th Edition : Oct. 31, 2013-00
15. OPERATION OF SENCOM pH/ORP
This chapter describes the screen operations of SENCOM pH/ORP, the object to be measured.
Further details of screen operations can also be found in section 1.2.
10.38
Tag:SENCOM
25.0
4mA 20mA PH1
°C
pH
19 mV
Execute:
Calibration
HOLD
Setup:
Commissioning
Change language
Start Quick Setup
Execute & Setup
◆Sensor setup
◆Measuremet setup
◆Output setup
◆Error configuration
◆Logbook configuration
◆Advanced setup
◆Display setup
Comissioning
◆Manual
◆Automatic
◆Sample
Calibration pH
◆Manual
◆Sample
Calibration ORP
◆Zero/Slope
◆Zero/Slope/ITP(3point)
◆Zero/Slope1,2(3point)
pH Manual
◆Zero/Slope
◆Zero/Slope/ITP(3point)
◆Zero/Slope1,2(3point)
pH Automatic
◆pH
◆ORP
◆Temperature
Calibration
HART ＞
PH201G ＞
Communication
◆Setting logbook
Logbook configuration
◆Main display
◆Trend
◆Auto Return
◆Adjust contrast
◆MONITOR display
Display setup
◆Enter values
Table mA
Change language
HOLD
Setup: Linear ＞
Table ＞
mA(Output)
◆x-axis: Timing
◆Y-axis: Limits
Trend
◆Additional text
Main display
◆Enter values
Matrix
Input 1 impedance: Low ＞
Input 2 impedance: Low ＞
Impedance setup
◆Temperature settings
◆Temp. compensation
◆Calibration settings
◆Impedance settings
◆Concentration
◆Sensor diag. settings
Measurement setup
Compensation: Manual ＞
Reference temp.
pH: Matrix
＞
TC ＞
ORP: TC ＞
Temp. comp.
◆Define heat cycle
◆Define SENCOM status
Sensor diag. setting
◆pH settings
◆ORP settings
◆rH settings
Cal. settings
◆Zero and Slope units
◆Limits and timing
◆Buffers (select set)
◆Zero/Slope/ITP
◆Auto correct(Zero, Slope)
Cal. set pH
Select buffer set:
Free programmable ＞
Buffers
mA: Output ＞
Simulate ＞
◆Configure Hold
Output setup
◆Settings
◆Tag
◆Passwords
◆Date/Time
◆Communication
◆Factory setup
Advanced setup
Wash contact: Enabled ＞
PH201G setup
◆Enter values
Buffer table 1 ◆Buffer table 1
◆Buffer table 2
◆Buffer table 3
Free programmable
Quick setup Seneor setup Date/Time Measurement setup
Temperature settings mA(output)
16.1
16.2
16.3
16.4
16.5
16.6
16.7
2.7
17.1
17.3
17.2
17.1.1
17.1.2
17.1.3
17.4
16.2.2
16.2.3
16.2.4
16.2.5
16.2.6
16.2.7
16.7.1
16.7.2
16.7.3
16.7.4
16.7.5
16.6.1
16.6.2
16.6.3
16.6.4
16.6.5
16.6.6
15.2 16.6.4 16.1 16.2.1
16.2.2 16.3
Figure 15.1 Menu structure of SENCOM pH/ORP (the number after the item refers to the relevant section)
15
SENCOM