beautypg.com

GF Signet 8900 Multi-Parameter Controller User Manual

Signet 8900 multi-parameter controller

background image

Signet 8900 Multi-Parameter Controller

Multi-Parameter

Controller

C1

2.50 µS/cm

F2

58.43 GPM

Relay 1

Relay 2

ENTER

3-8900.090-1
3-8900.090-1

Rev. K 01/13

English

Contents
1. Specifi

cations

2

2.

Description

4

2.1

Compatibility

4

2.2

System

Overview 5

3. Installation and Basic Functionality

6

3.1

Unpacking

6

3.2 Tools and Equipment Required

6

4.

Plug-in

Modules

6

4.1

I/O

Module

7

4.2

Power

Module

7

4.3

Output

Module

8

4.4

Relay

Module

8

4.5 8059 External Relay Module

9

5. Mounting the Base Unit

10

5.1

Panel

Mounting

10

5.2

Mounting

Accessories

11

6.

Wiring

12

6.1 Signal Type: Frequency

12

6.2

Digital

(S

3

L) Input wiring

13

6.2.1 Digital Cable Length Calculations 14

6.2.2 Digital Cable Routing Diagrams

15

6.3 Power Module (3-8900.402-X)

17

6.4 Output Module (3-8900.405-X)

17

6.5 Relay Module (3-8900.403-X)

18

6.6 8059 External Relay Module

18

7.

Operational

Overview

19

7.1 General Operation Flowchart

19

7.2

System

Confi

guration

20

7.3

Menu

Directory

20

8. System Setup Menu

21

8.1 System Setup: Channel Type

21

8.2 Automatic Sensor Recognition

22

8.3

Automatic

Channel

Assignment

22

8.4 Automatic Display Confi gurations

22

8.5 Other Automatic Displays

23

8.6 Displays for Derived Functions

23

Important Safety Information

Read and understand instruction manual before using
this product.

This unit is designed to be connected to equipment
which can be hazardous to persons and property if
used incorrectly. Read and understand all associated
equipment manuals and safety warnings before using
with this product.

Do not remove rear panel slot shields if the modules
are not installed.

Remove power to unit before wiring input and output
connections.

Wiring connections to this product should only be
performed by qualifi ed personnel.

Do not exceed published specifi cations in the use of
this product.

In case of communication error or loss of source
signal:

• Relays will be deactivated.
• Current outputs will go to 22.1 mA.
• Voltage outputs will go to 0 V.

9.

Channel

Settings 24

9.1 Channel Settings: Flow

24

9.2 Channel Settings: pH

25

9.3 Channel Settings: ORP

25

9.4 Channel Settings: Conductivity

26

9.5 Channel Settings: Pressure

27

9.6 Channel Settings: Temperature

27

9.7 Channel Settings: Level

28

9.8 Channel Settings: OTHER (4–20)

30

10.

Hold

Inputs

30

11. Relay Mode Descriptions

31

11.1 Relay Setup Menu

33

11.2 Advanced Relay Mode

34

12.

Output

35

13.

Calibration 36

13.1 Calibration: Flow

36

13.2 Calibration: pH

37

13.3 Calibration: ORP

37

13.4 Calibration: Conductivity

38

13.5 Calibration: Pressure

38

13.6 Calibration: Temperature

38

13.7 Calibration: Level

38

14.

Options

39

14.1 Password Security

39

Appendix A:

Derived Functions

40

Appendix B:

Level System Confi guration

41

Appendix C:

Conductivity & Temp Comp

43

Appendix D:

USP Limits

44

Appendix E:

Cloning using Digital (S

3

L)

45

Appendix F:

BTU Quick Start Guide

47

Appendix G:

8900 display messages

48

Ordering

Information 52