Yokogawa GC1000 Mark II Process Gas Chromatograph Instruction Manuals and User Guides
We have 4 Instruction Manuals and User Guides for GC1000 Mark II Process Gas Chromatograph Yokogawa
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 24 |
| Size: | 726 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 41 |
| Size: | 1.42 MB |
Show table of contents
Document Outline
| Recognized languages: | English |
|---|---|
| Pages: | 77 |
| Size: | 893 KB |
Show table of contents
Document Outline
- CONTENTS
- u Warning/Caution Labels
- 1. Principle of Gas Chromatograph
- 1.1 Sampling Mechanism
- 1.2 Component Separation Using Column
- 1.3 Detector
- 2. Terminology
- 2.1 Operation Terminology
- 2.2 Instrument Terminology
- 3. System Configuration
- 3.1 Type and Appearance
- 3.2 Components and Their Functions
- 3.2.1. Protection System
- 3.2.2 Electronic Section
- 3.2.3 Pressure and Flow Control Section
- 3.2.4 Isothermal Oven
- 3.2.5 Programmed-temperature Oven
- 3.2.6 Analyzer Base Sampling Section
- 3.3 Block Diagram
- 3.4 Internal Piping System Diagram
- 3.5 External Input and Output Signals
- 4. Outline of Software
- 4.1 Status and Operation Mode
- 4.1.1 Process
- 4.1.2 Manual
- 4.1.3 Lab
- 4.2 Stream
- 4.3 Method
- 4.4 Description of Actions
- 4.4.1 Actions of Stream Sequence
- 4.4.2 Actions of Stream (Continuous)
- 4.4.3 Actions of Stream (1 cycle)
- 4.4.4 Actions of Calibration
- 4.4.5 Actions of Validation
- 4.5 Computation and Processing
- 4.5.1 Peak Processing
- 4.5.2 Deviation processing
- 4.5.3 Additional processing
- 4.5.4 Signal Processing
- 4.6 Alarm Processing
- 5. Actions of External Input and Output Signals
- 5.1 Analog Hold Output
- 5.1.1 When Actual Stream is Specified for Stream Number (without Stream Identification Signal)
- 5.1.2 When Actual Stream is Specified for Stream Number (with Stream Identification Signal)
- 5.1.3 When "99" is Specified for Stream Number (with Stream Identification Signal)
- 5.2 Contact Output
- 5.2.1 Stream Sequence
- 5.2.2 Stream
- 5.2.3 Operation Mode
- 5.2.4 Alarm
- 5.2.5 Timing
- 5.3 Contact Input
- 5.4 Communication Input and Output
- 5.4.1 GC6 Type Output Data Format (Fixed to 45 Characters)
- 5.4.2 GC6 Type Input Data Format
- 5.4.3 GC8/GC1000 Type Output Data Format (Fixed to 45 Characters)
- 5.4.4 GC8/GC1000 Type Input Data Format
- 5.4.5 MODBUS Communication Data Specification
- u Revision Record
| Recognized languages: | English |
|---|---|
| Pages: | 105 |
| Size: | 4.39 MB |
Show table of contents
Document Outline
- Introduction
- Safety Precautions
- Documentation Conventions
- Copyright and Trademark Notices
- Installing the Maintenance Terminal
- 1. Overview of Maintenance Terminal
- 2. LCD Emulator Window
- 3. Analyzer Operation Window
- 3.1 Starting and Exiting the Maintenance Terminal
- 3.2 Layout of Analyzer Operation Window
- 3.3 Viewing the States of the Detector and Temperature Controller
- 3.4 Changing the User Level
- 3.5 Changing the Status/Operation Mode/Measurement Status
- 3.6 Changing the states of the Valves/Detectors/Temperature Controller
- 3.7 Changing the Range
- 3.8 Changing the Valves and Peak Information
- 3.9 Uploading and Downloading the Parameter Settings
- 3.10 Actions When Alarms Occur
- 4. Chromatogram Window
- 5. Alarm Windows
- 6. Analysis Results Windows
- 6.1 Opening and Closing an Analysis Results Window
- 6.2 Types and Layouts of Analysis Results Windows
- 6.3 Switching Between Analysis Results Windows
- 6.4 Saving and Retrieving Data
- 6.5 Processing and Re-saving Data
- 6.6 Graphing Historical Data
- 6.7 Resetting Historical Data
- 6.8 Opening the Help Window of an Analysis Results Window
- Appendix A Menus
- Appendix B Messages Summary
- Revision Information