Toshiba Tosvert VF-A5 - Manual (Page 20)

Table 5.1: Examples of selecting equipment for wiring
Appncabfe
motor
m
Inverter
Non-fuse breaker
(MCC8)
Magnetic
contactor (MC)
Overload relay
Th-Ry
Model
Rated
current
(A)
Toshiba
model
Rated
current
(A)
Toshiba
model
(Note 1)
cunvnt value
_ w
{Reference
vfeue]
Toshiba
model
0.4 -2004P 5 SS30 12 C12A 2.3 T11A
0.75 -2007P 10 SS30 12 C12A 4.2 T11A
1.5 -2015P 15 SS30 12 C12A 6.6 T11A
2.2 -2022P 20 SS30 12 C12A 9.3 Til A
3.7 -2037P 30 SS30 18 C20A 15 T20A
5.5 -2055P 50 ESSO 35 C35A 22 T35A
7.5 -2075P 60 EH100 50 C50A 28 T35A
11 -211 OP 100 EH100 65 C65A 43 T65A
15 -2150P 125 EH225 80 C80A 57 T65A
18.5 -2185P 125 EH225 93 C100A 70 T80A
22 -2220P 150 EH225 93 C100A 85 T125A
30 -2300P 200 EH225 180 C180A 108 T125A
37 -2370P 225 EH225 180 C180A 138 T150A
45 -2450P 250 EH400 220 C220A 162 T180A
55 -2550P 250 EH400 220 C220A 198 T220A
75 -2750P 500 SH600 300 C300A 3.6 T400A
0.75 -4007P 5 SS30 9 C12A 2.3 Til A
1.5 -4015P 10 SS30 9 C12A 3.6 T11A
2.2 -4022P 10 SS30 9 C12A 5.0 Til A
3.7 -4037P 15 SS30 9 C12A 8 T11A
5.5 -4055P 30 SS30 17 C20A 11 T20A
7.5 -4075P 30 SS30 17 C25A 15 T20A
11 -4110P 50 ESSO 33 C35A 22 T35A
15 -4150P 60 EH100 48 C50A 28 T35A
18.5 -4185P 75 EH100 50 C50A 35 T35A
22 -4220P 100 EH100 50 C50A 43 T65A
30 -4300P 125 EH225 80 C80A 57 T65A
37 -4370P 125 EH225 93 C100A 70 T80A
45 -4450P 150 EH225 180 C180A 85 T125A
55 -4550P 175 EH225 180 C180A 108 T125A
75 -4750P 225 EH225 220 C220A 138 T150A
Voltage
dass
Surge killer
Model
(Note^
Wire size
Main
ciicuit
(mm^
(Notes)
Control
dfcuit
(mm^
(Note 4)
Dynamic
braking
(mm®)
200V
class
2.0
Toshiba
model SS-2
or
Marcon
Bectronics
RFM2E224KD
2.0
2.0
2.0
0.75 or
larger
3.5
14
5.5
14
22
8.0
38
38
22
60
100
100 60
100
100x2
400V
class
2.0
Model SS-2
or
Marcon
Bectronics
RFM2H104KD
(400V system)
(Note 6)
2.0
2.0
2.0
0.75 or
larger
3.5
5.5
2.0
3.5
14
22
8.0
38
38
38 22
60
100
(Note 1) When selecting a magnetic contactor (MC) with 2a auxiliary contacts and using the auxiliary contacts for the control circuit,
parallel the 2a contacts to improve contact reliability.
(Note 2) Install a surge killer on the magnetic contactor or relay exciting coil.
(Note 3) The wire sizes for the input side R, S, T and output side U, V, W are shown. These sizes apply only when the wiring length is
less than 30m. Increase the wire sizes when the length exceeds 30m.
(Note 4) Use shielded wire.
(Note ^ Use a wire size 3.5mm® or more for the grounding wire.
(Note 6) 200V system: type SS-2 or Marcon Bectronics RFM2E224KD
-
14
-