Det-Tronics EQP Fire and Gas Detection/Releasing System - Manual (Page 3)

eQ3XXX CONtrOller INstAllAtION .......................... 3-14
enclosure requirements ............................................. 3-14
Mounting ..................................................................... 3-14
serial Interface Board ................................................. 3-14
Wiring .......................................................................... 3-15
Power Wiring ........................................................ 3-15
electrical Connections ......................................... 3-15
Controller to Controller Communication ...................... 3-19
Configuration ............................................................... 3-22
software Defined Addresses ............................... 3-22
eQ3XXX reDUNDANt CONtrOller INstAllAtION ... 3-22
enclosure requirements ............................................. 3-22
Mounting ..................................................................... 3-22
Wiring .......................................................................... 3-22
lON Wiring .................................................................. 3-22
High speed serial link (Hssl) ................................... 3-22
Configuration ............................................................... 3-23
s3 Configuration .................................................. 3-23
Controller Addresses ........................................... 3-23
Modbus ................................................................ 3-23
ControlNet ........................................................... 3-23
eQ21XXPs serIes POWer sUPPlY AND
POWer sUPPlY MONItOr INstAllAtION .................... 3-23
Mounting ..................................................................... 3-23
Wiring .......................................................................... 3-23
startup ........................................................................ 3-25
Measuring Battery voltage and Charging Current ....... 3-26
eQP2XX0Ps(–X) POWer sUPPlIes AND
reDUNDANCY MODUle INstAllAtION ........................ 3-26
Mounting ..................................................................... 3-26
Wiring .......................................................................... 3-26
startup ........................................................................ 3-29
eDIO MODUle INstAllAtION ......................................... 3-29
Configuration ............................................................... 3-33
8 CHANNel DCIO INstAllAtION .................................... 3-34
Mounting ..................................................................... 3-34
Wiring .......................................................................... 3-34
Configuration ............................................................... 3-38
8 CHANNel relAY MODUle INstAllAtION ................. 3-38
Mounting ..................................................................... 3-38
Wiring .......................................................................... 3-38
Configuration ............................................................... 3-39
ANAlOg INPUt MODUle INstAllAtION ....................... 3-40
Mounting ..................................................................... 3-40
Wiring .......................................................................... 3-40
Configuration ............................................................... 3-41
INtellIgeNt PrOteCtION MODUle INstAllAtION ....3-42
Wiring .............................................................................3-42
Configuration ..................................................................3-45
gAs DeteCtOr lOCAtION AND INstAllAtION ..................3-46
environments and substances that Affect gas Detector
Performance ........................................................ 3-46
eQ22xxDCU Digital Communication Unit used with
Det-tronics H2s/O2 sensors or other two-Wire
4-20 mA Devices ................................................. 3-47
Assembly and Wiring Procedure .......................... 3-47
sensor separation for DCU with H2s and O2
sensors ........................................................ 3-48
eQ22xxDCU Digital Communication Unit used with
PointWatch/DuctWatch ........................................ 3-49
Assembly and Wiring Procedure .......................... 3-49
sensor separation for DCU with PointWatch ...... 3-49
eQ22xxDCUeX Digital Communication Unit (used with
Det-tronics Combustible gas sensors) ............... 3-50
Mounting .............................................................. 3-50
Wiring .................................................................. 3-50
sensor separation with DCUeX .......................... 3-51
eQ25xxArM series Agent release Module ............... 3-53
Mounting .............................................................. 3-53
Wiring .................................................................. 3-53
supervised Output for Deluge and Pre-action ..... 3-55
Jumpers ............................................................... 3-55
Address setting ................................................... 3-55
eQ25xxsAM series signal Audible Module ............... 3-55
Mounting .............................................................. 3-55
Wiring .................................................................. 3-55
Jumpers ............................................................... 3-56
Address setting ................................................... 3-56
sYsteM CONFIgUrAtION .............................................. 3-57
setting Device Network addresses ............................. 3-57
Overview of Network Addresses .......................... 3-57
setting Field Device Addresses ........................... 3-57
tYPICAl APPlICAtIONs .................................................. 3-57
Table of Contents – Continued