Samsung CLX-9250ND-XAA - Manual (Page 82)

SyncThru™ Web Service_ 82
will wait before the server connection fails due to timeout. You
can set the time value between 1-300 second(s). The time value
should be 30 seconds or more for reliable operation over
congested enterprise networks.
Scan Security
You can set Scan related security settings.
• Digital Signature in PDF
- Certificate for Digital Signature in PDF: You can select the
certificate to use. For installing the digital certificates, refer to
"Digital Certificate" on page 86.
- Digital Signature in PDF: Check to enable the digital signature
in PDF files. This will only be available for scan to server, SMB,
and FTP.
E-mail Notification
When an error occurs or the consumables are running out, the machine
sends a notification to the administrator via e-mail. You can set whether
to use this feature or not. You can also select which alerts to receive and
when.
From the SyncThru™ Web Service, select the Settings tab > Machine
Settings > E-mail Notification.
• General
- E-mail Notification: Check to receive e-mail notification when
there is an alert.
• Recipients & Conditions: You can view the list of alerts and
add/delete/edit current alerts.
Adding an alert
1. From the SyncThru™ Web Service, select the Settings tab >
Machine Settings > E-mail Notification.
2. Click on the Add button under Recipients & Conditions.
A pop-up window appears.
3. Enter the recipients’ contact information under Recipients.
4. Select the alerts for which you want to receive notification from
under Notifications.
For consumable related alerts, you can set the remaining
percentage for which you want to receive notification; click
on Setting. For example, if you set this value to 10% for the
imaging unit, and the average imaging unit yield is 20,000
pages, when about 2,000 pages (10% of 20,000 pages) are
left, a notification will be sent.
5. Click the Apply.
Network Settings
You can set up the network environment to use your machine as a network
machine. Set the values and click on the Apply button on the upper right
corner of the page. You can also set the settings from the machine. Refer to
the network setup chapter (see "Network setup" on page 52).
From the SyncThru™ Web Service, select the Settings tab > Network
Settings.
General
From the SyncThru™ Web Service, select the Settings tab > Network
Settings > General.
You can set general machine information to use in the network and set
ethernet settings. Set the values and click the Apply button on the upper
right corner of the page. This feature is also available from the machine
(see "Ethernet" on page 54).
The Undo button clears all the values set so far.
• General: Set the general network settings.
- Host Name: Enter the host name of your machine.
- Location: Enter the location of your machine.
- Contact: Enter the name of the person in charge of the
machine. Administrator is set as a default.
• Ethernet: Set the general ethernet settings.
- Ethernet Speed: Choose the speed rate of the ethernet.
Automatic is recommended for all network environments.
- Actual Speed Rate: Shows the actual speed of the ethernet.
- MAC Address: Shows the MAC address of your machine.
TCP/IPv4
You can set IPv4 settings. Set the values and click the Apply button on
the upper right corner of the page. This feature is also available from the
machine (see "TCP/IP Protocol" on page 53).
From the SyncThru™ Web Service, select the Settings tab > Network
Settings > IPv4.
The Undo button clears all the values set so far.
• General: Set the general IPv4 settings.
- Assign an IP Address: Select the method for assigning an IP
address.
- Manually: Select to enter IP address/Subnet Mask/ Gateway
Address manually.
- Automatically: IP address/Subnet Mask/ Gateway Address
are automatically allocated by BOOTP/DHCP Server.
• If you check Auto IP, when the BOOTP or DHCP fail to
allocate IP address/Subnet Mask/ Gateway Address
after 2 minutes, the machine automatically allocates a
Link-Local IP address, which is the 169.254.0.0/16 set
of addresses defined in RFC 3927.
The Undo button clears all the values set so far.
• Domain Name: Set the DNS server settings.
- Host Name: Shows the host name. You can change the name
in Settings tab > Network Settings > General (see "General"
on page 82).
- Domain Name: Enter the domain name. You can enter up to
128 characters.
- Primary DNS Server: Enter the address of the DNS server you
want to use primarily.
- Secondary DNS Server: Enter the address of the DNS server
you want to use as an alternative.
- Dynamic DNS Registration: Check to enable dynamic DNS
registration. If this option is enabled, machine registers its host
name and domain name to configured DNS servers dynamically.
Also, if this option is enabled and DHCP is selected, DHCP
FQDN options is automatically disabled.
- Authentication Method: Select the authentication method.
Dynamic DNS Registration needs to be checked to set this
option.
• WINS: Set the WINS server settings.
- WINS Protocol: Check to enable WINS server.
- Primary WINS Server: Enter the address of the WINS server
you want to use primarily.
- Secondary WINS Server: Enter the address of the WINS server