beautypg.com

B.85, Sour, B.86 – KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.01 to 2.37 User Manual

Page 165: B.87, B.88, B.89, B.90, B.85, b.86, B.89, b.87, B.89, b.90

background image

BOP-1K 022108

B-19

B.85 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:BOTH COMMAND

VOLT:PROT:LIM[:BOTH]

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIMit[:BOTH]
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIM[:BOTH
where is bewteen minimum (box) value (Figure 1-2) and 1% above rated (nominal) output
voltage.

Description: Establishes the maximum value possible for both the positive and negative protection limits for volt-

age. Requires MEM:UPD (PAR. B.11) to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for spe-
cial programming considerations.

B.86 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]? QUERY

VOLT:PROT:LIM[:BOTH]?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM[:BOTH]?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]?
Returns ,

Description: Identifies the maximum value possible for protection limits for voltage (positive, negative); maximum is

1% greater than rated output voltage.

B.87 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative COMMAND

VOLT:PROT:LIM:NEG

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:NEG
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative
where is between minimum (box) value (Figure 1-2) and 1% above rated (nominal) output
voltage.
Description:Establishes the minimum (maximum absolute) value possible for the negative protection
limit for voltage. This may be set up to 1% greater than rated voltage. Requires MEM:UPD (PAR. B.11)
to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.

B.88 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative? QUERY

VOLT:PROT:LIM:NEG?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:NEG?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative?
Returns:
Description:Identifies the minimum (maximum absolute) value possible for the negative protection limit
for voltage.

B.89 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive COMMAND

VOLT:PROT:LIM:POS

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:POS
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive
where is bewteen minimum (box) value (Figure 1-2) and 1% above rated (nominal) output
voltage.
Description:Establishes the maximum value possible for the positive protection limit for voltage. This
may be set up to 1% greater than rated voltage. Requires MEM:UPD (PAR. B.11) to save for power
up. See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.

B.90 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive? QUERY

VOLT:PROT:LIM:POS?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:POS?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive?
Returns:
Description:Identifies the maximum value possible for the positive protection limit for voltage.