KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.01 to 2.37 - Manual (Page 12)

iv
BOP-1K 022108
TABLE OF CONTENTS
SECTION PAGE
3.6.7 Status Reporting ............................................................................................................................... 3-60
3.6.7.1 Status Reporting Structure.......................................................................................................... 3-60
3.6.7.2 Operational Status Register ........................................................................................................ 3-62
3.6.7.3 QUEStionable Status Register.................................................................................................... 3-62
3.6.8 SCPI Program Examples .................................................................................................................. 3-62
SECTION 4 - CALIBRATION
4.1 General ................................................................................................................................................... 4-1
4.2 Test Equipment Requirements ............................................................................................................... 4-3
4.3 Calibration using Remote SCPI commands via GPIB or RS 232 Interface ............................................ 4-4
4.3.1 Calibration Procedure using SCPI Commands................................................................................. 4-5
4.4 Calibration Using Front Panel Keypad in Local Mode ............................................................................ 4-10
4.4.1 Understanding the Calibration Process ............................................................................................ 4-10
4.4.2 Calibration Procedure using Local Mode .......................................................................................... 4-12
4.4.3 Calibration using VISA Driver Soft Panel.......................................................................................... 4-16
4.5 Calibration Storage ................................................................................................................................. 4-16
APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-2
A.5 *ESR? — Event Status Register Query.................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query .................................................................................................... A-3
A.9 *OPT? — Options Query ........................................................................................................................ A-4
A.10 *RCL — Recall Command ...................................................................................................................... A-4
A.11 *RST — Reset Command....................................................................................................................... A-4
A.12 *SAV — Save Command........................................................................................................................ A-4
A.13 *SRE — Service Request Enable Command ......................................................................................... A-5
A.14 *SRE? — Service Request Enable Query .............................................................................................. A-5
A.15 *STB? — Status Byte Register Query .................................................................................................... A-5
A.16 *TRG — Trigger Command .................................................................................................................... A-5
A.17 *TST? — Self Test Query ....................................................................................................................... A-6
A.18 *WAI — Wait-To-Continue Command .................................................................................................... A-6
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ............................................................................................................................................. B-1
B.2 Numerical Values.................................................................................................................................... B-2
B.3 ABOR t Command................................................................................................................................... B-2
B.4 CAL Commands and Queries................................................................................................................. B-2
B.5 INIT iate [:IMM ediate ] Command ............................................................................................................ B-3
B.6 INIT iate :CONT inuous Command .......................................................................................................... B-3
B.7 INIT iate :CONT inuous Query ................................................................................................................. B-3
B.8 MEAS ure [:SCAL ar ]:CURR ent [:DC]? Query.......................................................................................... B-3
B.9 MEAS ure [:SCAL ar ]:VOLT age [:DC]? Query .......................................................................................... B-3
B.10 MEM ory :REL oad Command.................................................................................................................. B-3
B.11 MEM ory :UPD ate Command .................................................................................................................. B-3
B.12 OUTP ut [:STAT e ] Command................................................................................................................... B-4
B.13 OUTP ut [ : STAT e ] Query ......................................................................................................................... B-5
B.14 OUTP ut :MODE Command ..................................................................................................................... B-5
B.15 OUTP ut :MODE? Query.......................................................................................................................... B-5
B.16 [SOUR ce :]FUNC tion :MODE Command ................................................................................................ B-5