KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.01 to 2.37 - Manual (Page 161)

BOP-1K 022108
B-15
B.59 [SOURce:]CURRent[:LEVel]:PROTect:LIMit[:BOTH] COMMAND
CURR:PROT:LIM[:BOTH]
Syntax: Short Form: [SOUR:]CURR[:LEV]:PROT:LIM[:BOTH]
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit:[BOTH
where is between minimum (box) value (Figure 1-2) and 1% above rated (nominal) output
current.
Description: Establishes the maximum value possible for both the positive and negative protection limits for cur-
rent. Requires MEM:UPD (PAR. B.11) to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for spe-
cial programming considerations.
B.60 [SOURce:]CURRent[:LEVel]:PROTect:LIMit[:BOTH]? QUERY
CURR:PROT:LIM:[:BOTH]?
Syntax: Short Form: [SOUR:]CURR[:LEV]:PROT:LIM[:BOTH]?
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit[:BOTH]?
Returns ,
Description: Identifies the maximum value possible for protection limits for current (positive, negative); maximum is
1% greater than rated output current.
B.61 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:NEGative COMMAND
CURR:PROT:LIM:NEG
Syntax: Short Form: [SOUR:]CURR[:LEV]:PROT:LIM:NEG
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit:NEGative
where is between minimum (box) value (Figure 1-2) and 1% above rated (nominal) output
current.
Description: Establishes the minimum (maximum absolute) value possible for the negative protection limit for cur-
rent. This may be set up to 1% greater than rated current. Requires MEM:UPD (PAR. B.11) to save for
power up. See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.
B.62 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:NEGative? QUERY
CURR:PROT:LIM:NEG?
Syntax: Short Form: [SOUR:]CURR[:LEV]:PROT:LIM:NEG?
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit:NEGative?
Returns:
Description: Identifies the minimum (maximum absolute) value possible for the negative protection limit for current.
B.63 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:POSitive COMMAND
CURR:PROT:LIM:POS
Syntax: Short Form: [SOUR:]CURR[:LEV]:PROT:LIM:POS
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit:POSitive
where is between minimum (box) value (Figure 1-2) and 1% above rated (nominal) output
current.
Description: Establishes the maximum value possible for the positive protection limit for current. This may be set
up to 1% greater than rated current. Requires MEM:UPD (PAR. B.11) to save for power up. See PAR.
3.5.2.2 and Figure 3-16 for special programming considerations.
B.64 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:POSitive? QUERY
CURR:PROT:LIM:POS?
Syntax: Short Form: [SOUR:]CURR[:LEV]:PROT:LIM:POS?
Long Form: [SOURce:]CURRent[:LEVel]:PROTect:LIMit:POSitive?
Returns:
Description:Identifies the maximum value possible for the positive protection limit for current.