Yaskawa Varispeed 626M5 User Manual
User's manual
This manual is related to the following products:
Table of contents
Document Outline
- Front Cover
- PREFACE
- Notes for Safe Operation
- Notes for Inverter and Converter
- Notes for Motor
- Warranty Information
- Visual Aids
- CONTENTS
- Table of Contents
- 1 Introduction
- 2 Handling
- 3 Wiring
- 4 Control Signals
- 5 Operating the Digital Operator
- 6 Trial Operation
- 6.1 Procedure
- 6.2 Trial Operation Procedure
- 6.3 Converter and Inverter LED Displays
- 6.4 Constant Settings
- 6.4.1 User Constant Functions Table
- 6.4.2 Soft Start Time Setting (TSFS: C1-10)
- 6.4.3 Load Factor Meter Full Scale (LMFS: C1-18)
- 6.4.4 Zero Speed Detection Level (ZSLV L : C1-19)
- 6.4.5 Speed Agree Width (AGRBD: C1-20)
- 6.4.6 Speed Detection Level and Detection Width (SDLV L : C1-21, SDHYS: C1-22)
- 6.4.7 Torque Detection Signal Operation Level (TDLV L : C1-23)
- 6.4.8 External Control Torque Limit Level (TLEXT: C1-24)
- 6.4.9 Motor Code Selection (MTR: C1-25)
- 6.4.10 Rated Speed (S100: C1-26)
- 6.4.11 Gear Ratios (RHGR: C1-27, RMGR: C1-28, RLGR: C1-29)
- 6.4.12 Servo Mode Flux and Base Speed Ratio (dia SVH: C1-31, RBSH: C1-32, dia SVL: C1-33, RSBL: C1-34)
- 6.4.13 Positioning Completion Detection Width (ZFIN : C2-09 and C3-09) and Positioning Completion Cancel Width (ZCAN: C2-10 and C3-10)
- 6.4.14 Orientation Speed (SORT : C2-11 and C3-11)
- 6.4.15 BCD Stop Position Reference Resolution (PBCD: C2-12 and C3-12)
- 6.5 Speed Control Mode Adjustment Procedure
- 7 Wide Constant Power Control Using Winding Selection
- 8 Orientation Control Using an Encoder
- 8.1 Device Configuration
- 8.2 Standard Connection Diagram
- 8.3 Orientation Specifications
- 8.4 Dimensions
- 8.5 Load Shaft Encoder Connector Terminal Arrangement
- 8.6 Important Points for Encoder Mounting and Wiring
- 8.7 Stop Position Reference Signals
- 8.8 Functions
- 8.9 Encoder Orientation Control Mode Adjustment Procedure
- 9 Magnetic Sensor Orientation Control
- 9.1 Device Configuration
- 9.2 Standard Connections
- 9.3 Orientation Specifications
- 9.4 Dimensions
- 9.5 Connections between Devices
- 9.6 Control Signal Connector Terminal Arrangement
- 9.7 Magnet and Magnetic Sensor Mountings
- 9.8 Mounting Precautions
- 9.9 Stop Position Reference Signal Details
- 9.10 Functions
- 9.11 Magnetic Sensor Orientation Control Mode Adjustment Procedure
- 10 Control Constants
- 11 Operating Status Displays
- 12 Troubleshooting
- 13 Maintenance and Inspection
- 14 Specifications
- 14.1 Drives
- 14.2 Standard Motor Specifications
- 14.3 Options and Peripheral Units
- 14.3.1 AC Reactor
- 14.3.2 Molded Case Circuit Breaker and Magnetic Contactor
- 14.3.3 Magnetic Contactor Specifications for Winding Selection
- 14.3.4 Busbar and Cable Kits for Connecting Units
- 14.3.5 Digital Operator and Connector Cables
- 14.3.6 Connector Kits
- 14.3.7 Noise Filters (Input)
- 14.3.8 Surge Absorbers
- 15 Appendix
- Back Cover