Comtech EF Data SMS-7000 - Manual (Page 129)

SMS-7000 Modem Protection Switch Remote Control Operation
Rev. 3 Draft A–13
Backup
Modem
Fault Status
Summary Command:
Response: >add/MFS_Bn'cr'
MOD_xxx'cr'
DMD_xxx'cr''lf'] Where: n = 1 or 2 (backup modem number).
Modulator Status (OK/FLT)
Demodulator Status (OK/FLT)
Prime
Modem
Fault Status
Summary Command:
Response: >add/MFS_n'cr'
MOD_xxx'cr'
DMD_xxx'cr''lf'] Where: n = 1 to 8 (prime modem number).
Modulator Status (OK/FLT)
Demodulator Status (OK/FLT)
Transmit
Operational
Faults
Status Command:
Response: >add/TOFS_'cr'
MOD_1_xxx'cr'
MOD_2_xxx'cr'
MOD_3_xxx'cr'
MOD_4_xxx'cr'
MOD_5_xxx'cr'
MOD_6_xxx'cr'
MOD_7_xxx'cr'
MOD_8_xxx'cr'
SFLT_xx'cr''lf']
Prime #1 TX Operational Status (OK/FLT)
Prime #2 TX Operational Status (OK/FLT)
Prime #3 TX Operational Status (OK/FLT)
Prime #4 TX Operational Status (OK/FLT)
Prime #5 TX Operational Status (OK/FLT)
Prime #6 TX Operational Status (OK/FLT)
Prime #7 TX Operational Status (OK/FLT)
Prime #8 TX Operational Status (OK/FLT)
Number of Stored Faults Logged (0 through 10)
Receive
Operational
Faults
Status Command:
Response: >add/ROFS_'cr'
DMD_1_xxx'cr'
DMD_2_xxx'cr'
DMD_3_xxx'cr'
DMD_4_xxx'cr'
DMD_5_xxx'cr'
DMD_6_xxx'cr'
DMD_7_xxx'cr'
DMD_8_xxx'cr'
SFLT_xx'cr''lf']
Prime #1 RX Operational Status (OK/FLT)
Prime #2 RX Operational Status (OK/FLT)
Prime #3 RX Operational Status (OK/FLT)
Prime #4 RX Operational Status (OK/FLT)
Prime #5 RX Operational Status (OK/FLT)
Prime #6 RX Operational Status (OK/FLT)
Prime #7 RX Operational Status (OK/FLT)
Prime #8 RX Operational Status (OK/FLT)
Number of Stored Faults Logged (0 through 10)
Backup
Modem
System
Fault Status
Summary Command:
Response: >add/SFS_Bn'cr'
COMM_xxx'cr'
MOD_CONFIG_VFY_xxx'cr'
DMD_CONFIG_VFY_xxx'cr'
ADD_xxx'cr'
MOD_CONFIG_LOAD_xxx'cr'
DMD_CONFIG_LOAD_xxx'cr'
PRIME_ASSIGNED_xxx'cr'
MU_COMM_xxx'cr'
(See Note)
MU_ADD_xxx'cr' (See Note)
SFLT_xx'cr''lf']
Where: n = 1 or 2 (backup modem number).
Modem Communications (OK/FLT)
Modulator Config Verify (OK/FLT)
Demodulator Config Verify (OK/FLT)
Backup Modem Address (OK/FLT)
Modulator Config Loaded (OK/FLT)
Demodulator Config Loaded (OK/FLT)
Primes Assigned to Backup (OK/FLT)
Multiplexer Unit Communications (OK/FLT)
Multiplexer Unit Address (OK/FLT)
Number of Stored Faults Logged (0 through 10)
Note: Status only returned if multiplexer unit is attached.
Prime
Modem
System
Fault Status
Summary Command:
Response: >add/SFS_n'cr'
COMM_xxx'cr'
MOD_CONFIG_VFY_xxx'cr'
DMD_CONFIG_VFY_xxx'cr'
ADD_xxx'cr'
MOD_CONFIG_LOAD_xxx'cr'
DMD_CONFIG_LOAD_xxx'cr'
PRIMES_ASSIGNMENT_xxx'cr'
MU_COMM_xxx'cr'
(See Note)
MU_ADD_xxx'cr' (See Note)
SFLT_xx'cr''lf']
Where: n = 1 to 8 (prime modem number).
Modem Communications (OK/FLT)
Modulator Config Verify (OK/FLT)
Demodulator Config Verify (OK/FLT)
Prime Modem Address (OK/FLT)
Modulator Config Loaded (OK/FLT)
Demodulator Config Loaded (OK/FLT)
Prime Assigned to Backup (OK/FLT)
Multiplexer Unit Communications (OK/FLT)
Multiplexer Unit Address (OK/FLT)
Number of Stored Faults Logged (0 through 10)
Note: Status only returned if multiplexer unit is attached.