Comtech EF Data SMS-7000 User Manual
Page 128
Remote Control Operation
SMS-7000 Modem Protection Switch
A–12
Rev. 3 Draft
Prime
Demodulato
r Config.
Status
Command:
Response:
DA_yyy'cr'
DP_y'cr'
(Note 1)
MP_y'cr'
(Note 2)
DD_yyy.y'cr'
(Note 1)
MD_yyy.y'cr'
(Note 2)
ADD_mmm'cr'
MU_xxx'cr'
MUA_mmm'cr'
(Note 3)
DID_xxxxx'cr'
ECLK_xxxxx'cr'
IDI_xxxx'cr''lf']
Where: n = 1 to 8 (prime modem number).
Demodulator Active (YES/NO)
Demodulator Priority
Modem Priority
Demodulator Delay
Modem Delay
Modem Address
Multiplexer Unit Attached (YES/NO)
Multiplexer Unit Address
Drop & Insert Data (BAL/UNBAL)
External Clock (BAL/UNBAL)
Insert Data Input (LOOP/NORM)
The prime demodulator configuration status command
causes a block of data to be returned by the SMS-7000. The
block of data reflects the stored configuration of the prime
modem selected.
Notes:
1. Status only returned in Independent Mode.
2. Status only returned in Dependent Mode.
3. Status only returned if multiplexer unit is attached.
Modulator
Status
Command:
Response:
MOD_1_xxx'cr'
MOD_2_xxx'cr'
MOD_3_xxx'cr'
MOD_4_xxx'cr'
MOD_5_xxx'cr'
MOD_6_xxx'cr'
MOD_7_xxx'cr'
MOD_8_xxx'cr'
MOD_B1_xxx'cr'
MOD_B2_xxx'cr''lf']
Prime #1 Modulator Status (OK/FLT)
Prime #2 Modulator Status (OK/FLT)
Prime #3 Modulator Status (OK/FLT)
Prime #4 Modulator Status (OK/FLT)
Prime #5 Modulator Status (OK/FLT)
Prime #6 Modulator Status (OK/FLT)
Prime #7 Modulator Status (OK/FLT)
Prime #8 Modulator Status (OK/FLT)
Backup #1 Modulator Status (OK/FLT)
Backup #2 Modulator Status (OK/FLT)
The modulator status is returned as a block of data which
provides fault information of all 'active' backup and prime
modulators.
Note: Response shown is for a system with all possible
backup modulators and prime modulators active. Only
active modulator status will be reported.
Demodulato
r Status
Command:
Response:
DMD_1_xxx'cr'
DMD_2_xxx'cr'
DMD_3_xxx'cr'
DMD_4_xxx'cr'
DMD_5_xxx'cr'
DMD_6_xxx'cr'
DMD_7_xxx'cr'
DMD_8_xxx'cr'
DMD_B1_xxx'cr'
DMD_B2_xxx'cr''lf']
Prime #1 Demodulator Status (OK/FLT)
Prime #2 Demodulator Status (OK/FLT)
Prime #3 Demodulator Status (OK/FLT)
Prime #4 Demodulator Status (OK/FLT)
Prime #5 Demodulator Status (OK/FLT)
Prime #6 Demodulator Status (OK/FLT)
Prime #7 Demodulator Status (OK/FLT)
Prime #8 Demodulator Status (OK/FLT)
Backup #1 Demodulator Status (OK/FLT)
Backup #2 Demodulator Status (OK/FLT)
The demodulator status is returned as a block of data which
provides fault information of all 'active' backup and prime
demodulators.
Note: Response shown is for a system with all possible
backup demodulators and prime demodulators active. Only
active demodulator status will be reported.