Kenwood KRF-V8881 D - Manual (Page 9)

VR-309O/Vfl-SOBO/KRF-V8381 D/Kflf-y7771D [En/K]
Connecting the system control
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of
convenient system control operations.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown
below.
[XSB]
Mode : lets you combine
[XS, [XSBl.
and
CXU
terminals
SLTB Mode : for SLTEl terminals only
This unit is compatible with both [XS8j and 1SL16| modes. It comes from the factory set to the fSLl5] mode To switch to the IXS8f mode, follow
the instructions in “SWITCHING FROM ISL16! TO [XSSI" below.
EXAMPLE: IXSB] mode connections
Tha underlined portion represents the setting o1 the system control moda.
EXAMPLE; [XS16I mode connections
The uncferltned portion repfesants the sstiing of the system control mode.
[SL161 iXSS]
ISL161
[SL16]
[SL16][MHKS8HXS1
[SL161 [XS] IXS81
[XS]
Receiver
DVD player
MD recorder
Cassette deck
SYSTEM
CONTROL
cord
CD player
Record player
ISL16] [XSSI
[SLIfil
rSLiS!
[SL16Ì [XS] IXSS] [XR]
[SLIfil IXSl IXSS]
[XS]
SYSTEM
CONTROL
cord
• In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must
be connected to the CD'jacks. To u.se a cassette deck (of MD recorder! it must be connected to the TAPE1/MD jacks. When using more than one
CD player (etc.! only the one connected to the specified jacks may be connected for system control.
• Somo CD players and cassette decks are not compatible with the [SL16] system control mode, 8e sure to use the (XS8) system control mode
when making system connections with equipment that is not ¡SL161 compatible.
• Some MD players are not system-control compatible The system control function is not availabla when a MD player is used by connecting it
through a digital input. You cannot connect the system control cord to this kind of equipment.
1, [SL161 equipment cannot be combined with [XR|, [XSj, and ¡XS8[ equipment for system operations. If your
equipment consists of this kind of combination, please do not connect any system control cord.s. Even without
system control cords, normal operations can be carried out without effecting performance.
2, Do not connect system control cords to any components other than those specified by KENWOOD, it may
cause a malfunction and damage your equipment,
3, Be sure the system control plugs are inserted all the way in to the system control terminals.
SrST£M CONTROL OPERATIONS
Remote Control
Lets you operate this unit with the system remote supplied
with the receiver,
Automatic Operation (except [XR] equipment!
When you start playback from a source component, the input
selector on this unit switches to that component automati*
cally.
Synchronized Recording (except [XR] equipment!
Lets you synchronize recording with the start of playback
when recording from CD, MD or analog discs.
SWITCHING FROM [SL W] TO [XS8]
You can easily change the system control mode by adjusting the
position of the SYSTEM CONTROL switch on the rear panel.
Do this operation after completing all connections.
For[SLl6| g|_^g ](gg For(XS81
This operation will not effect items stored in the memory.
■ After switching the system control mode, turn the power off and
then on once to confirm the new setting
Registering setup codes for KENWOOD audio components
* Once you finish making the system connections, be sure to register tfte appropriate setup code for each component.
• If you own remote controllable KENWOOD audio components that are not compatible with system control (or cannot be combined with your
other system control components), registering the setup code enables you to control those components using the remote control supplied
with this unit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components,
see "Setup for controlling AV components"