Kenwood KRF-V8881 D - Manual (Page 26)

Setup for playing two CD players from Room A and Room B
Wm Connect CD players.
vH-aoao/vR-aoao/KRF-vaaei d / krfv ?-/? 1 o ¡En/Kj
-^Ri^iK2iCiMl»™kA!iHi,-"rÌÌ8i*jiÉÀbkU8é.'«'teÌ>!*iyESÉ*iT'.M.rf^r'^E... -№ IIB-É^i »lU ■ Il rtj» .r. i i
The connection as described below is required when a KEWWOOD CD olaveTamJ a rn ni»u«r ’ , . — ——,
when two non-KENWOOD CD players a^e connected for listenino in "Room manufacturer are connected or
______ _____________________ ^ _» are connected ror listening m Room A and Room B". However, note that it is not possible to
connect and control two CD players from a same manufacturer.'
Connect the output of the first CD player to the CD1 input Jacks on the rear panel so that it is remote rontmM«rf -mr.,»»
fixed segments. Connect the output of the second CD player to the CD2/TAPE2 MONITOR input jacks on the rear n n i
remote controlled as the "CD2/Tape2" from the fixed segments.
'*
Operation in the “Setup Multi Room"menu.
• Display the "Setup Multi
Room" menu screen.
• To listen in "Room A" set
"SPEAKERS A" to ON
• To listen in "Room B", set
"SPEAKERS B" to ON,
Operation for displaying the "Setup Multi Room" menu screen :
O Select the "Main Menu" icon.
© Select the “Stp" icon.
© Select the "Multi Room" icon.
Operation in the Setup Multi Room" menu screen ;
O Select and set the "Multi Room" icon to "Yes",
© Select and set the “Zone Sefect" icon to "Room A" or
"Room 8" according to your location.
® Press and hold the "DtSPLAY MODE" key on the main
unit for more then 2 seconds to set the )R RECEIVER
location to "IR RECEIVER B".
Operation in the "Setup Input" menu.
• Display the "Setup Input"
menu screen,
• In this screen, perform the
setup for controlling the 2 nd
CD player.
Operation for displaying the "Setup input" menu screen i
O Sefect the "Main Menu" icon,
© Select the "Stp" icon.
O Select the "Input" icon.
Operation in the "Setup Input" menu screen :
© Select and set the "CD2/Tape2" icon to "Tape2".
Setup IR.
In step 6 of the procedure in Assigning the connected components to the selected inn*»»«" * ir»« T.................... ,
manufacturers of thetwoCD players for the “CD1" and "T^oe?' inonfrrell.^^^^
component only when the "CD! " synchro cord can be connected to the “CD 1"
component is a KENWOOD CD player.
Setup for playing a CD player from Room A and Room B (Other CO player than the Muht-raam capability CO Player)
Connect the CD player.
To play a CD player other than the KENWOOD Twin Pick CD Plaver in "Room a" and "Reee, a" ..Z TZZ I I ——
to therm I ui ricK ou riayer In MOomA and Room B , connect the output of the CD player
to the CD1 input jacks on the rear panel so that it is remote controlled as the "GDI" input.
Operation in the “Setup Multi Room” menu.
Perform the same setup operation as in step © of "Setup for playing two CD players from Room A and Room B".
Operation in the "Setup Input" menu.
Perform the same setup operation as in step B of "Setup for playing two CD players from Room A and Room B"
[1 Setup IR.
the connected components to theselected inputs", select the^CDl" input and inpuTtli7
setup code for KENWOOD system control. The synchro cord can be connected to the "CDI" component only when the "CDl"
comporrent is a KENWOOD CD player.
t i