Kenwood KRF-V8881 D - Manual (Page 47)

VR-S0aa/VH-Sae0/KRF-V88ei D/KRF-V7771 □ [En/K)
When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUTSELECTOR
to select "Tapel" or "MD" according to the connected component.
Recording a music source
О Select the recording source.
Щ .± ^ Й Ш *1;
£13 1ЯЯ1 gyi £J3 1E3
'.vfi "<.7' V ki » o ) vii«îï Vid«iï VUtKA *У*С*
The icons differ accord in g
to the setup of “Setup IR"
etc.
© Put the MD recorder or cassette deck to record-pause mode,
® Select the "Remote Mode" icon from the fixed segments.
@ Select the "MD/Tapel" icon.
(|; Select the MD or cassette deck control icon and put it to
record-pause mode.
© Play the source and record it.
• When the "Remote Mode" icon is selected, the icons of the
components assigned to the inputs, Such as the "GDI", "Video 1",
"VideoZ", "Videos" and "MD/Tapel" icons blink for a few
seconds.
By selecting a blinking icon, the selected component can be
controlled without switching the input selector. (The "Remote
Mode" icon can be used to put the recording component to pause
mode without switching the input selector J
When an icon that is not blinking is selected, the input selector is
switched automatically
• For the recording procedure of the MD recorder or cassette deck,
refer to its instrucrion manual
Copying tape (TAPE1 -► fÀPÙj
S Ш Й i
Wl ¥ie**t yIeiHMI y»#w»» *V.»4* i. ■ I <”'^1
©Select the "MD/Tapel" input.
© Startplayback of the cassette deck connected to the MD/TAPE1
input jacks, then start recording of that connected to theCD2/
TAPE2 MONITOR input jacks.
Caution for recording
Digital -*• digital recording
The digital signal input through DIGITAL IN is output digitally at
the OPTICAL jack.
Make sure the following points to record a digital signal input
into the receiver. (The DTS and Dolby Digital (AC-3) signals can­
not be recorded.)
©Connect the digital output from the source component to the
digital input of the receiver,
© Connect the digital output (OPTICAL jack) of the receiver to the
digital input (OPTICAL jack) of the MD recorder.
O Record the signal on the recorder component (MD recorder).
Digital -*■ analog recording
By reproducing the digital signal input to the receiver in stereo
(surround mode), the signal can be recorded in analog with the
following procedure.
© Set up the recorder component ready for recording
© Select the receiver's input to the source component,
© Play the desirad software.
© Set the "Input Digital" icon from "Auto" to "Manual".
© In the "Lstn Mode" menu screen, select the "Stereo" icon.
© Play the software from the beginning and record it.
• Do not switch to "CD2/Tape2 (Monitor)" during recording.
This may cause the interruption of the recording.
Note on CD2/ Tape2 (Monitor) .
The following operations are made available by setting the "CD2/Tape2 (Monitor)" Icon on the "Setup Input" menu screen to
"Tape2 (Monitor)". However, remember that these functions are available only when the analog input/output aroused. If the
"CD2/Tape2" icon in the fixed segments is selected during playback of
a digital input, the input is switched to the analog input
and noise may be generated.
ICON
DISPLAY
С0г/ТАРЕ2
MONITOR
"Tape! (Monitor)" setup menu screen
For the setup of the remote control unit, please read "Set "CD2/Tape2'"'.
Using "CD2/Tape2”
The CD2/TAPE2 MONITOR input jacks of the mam unit accept a cassette deck or graphic egualizer.
When a graphic equalizer is connected, set "CD2/Tape2" to "Tape2" and select the "CD2/Tape2"
con in the fixed segments to on.
When a 3-head cassette deck is connected to the CD2/TAPE2 MONITOR input jacks, the recorded
audio can be monitored during recording, and turning "CD2/T8pe2" on and off allows you to
compare the source audio and recorded audio. Refer to the Instruction manuals of the connectecl
components for their operating procedures.
The "C02/Tape2 (Monitor)" function is not available during playback of a digital input Selecting
"CD2/Tape2 (Monitor)“ during digital input playback switches the input to the analog input.